View KSZ8091RND-EVAL_8864154.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ksz8091rna/ksz8091rnd 10base - t/100base - tx physical layer transceiver revision 1.2 linkmd is a registered trademark of micrel, inc. micrel inc. ? 2180 fortune drive ? san jose, ca 95131 ? usa ? tel +1 (408) 944 - 0800 ? fax + 1 (408) 474 - 1000 ? http://www.micrel.com august 31 , 2015 revision 1.2 general description the ksz8091rna is a single - supply 10base - t/100base - tx ethernet physical - layer transceiver for transmission and reception of data over standard cat - 5 unshielded twisted pair (utp) cable. the ksz8091rna is a highly - integrated phy solution. it reduces board cost and simplifies board layout by using on- chip termination resistors for the differential pairs and by integrating a low - noise regulator to supply the 1.2v co re, and by offering a flexible 1.8/2.5/3.3v digital i/o interface. the ksz8091rna offers the reduced media independent interface (rmii) for direct connection with rmii - compliant ethernet mac processors and switches. as the power - up default, the ksz8091rna uses a 25mhz crystal to generate all required clocks, including the 50mhz rmii reference clock output for the mac. the ksz8091rnd takes in the 50mhz rmii reference clock as the power - up default. energy efficient ethernet (eee) provides further power saving during idle traffic periods and wake - on - lan (wol) provides a mechanism for the ksz8091rna to wake up a system that is in standby power mode. the ksz8091rna and ksz8091rnd are available in 24 - pin, lead - free qfn packages (see ordering information ). datasheets and support documentation are available on website at: www.micrel.com . features ? single - chip 10base - t/100base - tx ieee 802.3 compliant ethernet transceiver ? rmii v1.2 interface support with a 50mhz reference clock output to mac, and an option to input a 50mhz reference clock ? rmii back - to - back mode support for a 100mbps copper repeater ? mdc/mdio management interface for phy register configuration ? programmable interrupt output ? led outputs for link and activity status indication ? on - chip termination resistors for the differential pairs ? baseline wander correction ? hp auto mdi/mdi - x to reliably detect and correct straight - t hrough and crossover cable connections with disable and enable option ? auto - negotiation to automatically select the highest link - up speed (10/100mbps) and duplex (half/full) ? energy efficient ethernet (eee) support with low - power idle (lpi) mode for 100base tx and transmit amplitude reduction with 10base - te option ? wake - o n - lan (w o l) support with either magic packet, link status change, or robust custom - packet detection ? linkmd ? tdr - based cable diagnostics to identify faulty copper cabling ? hbm esd rating (6 k v) functional diagram
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 2 revision 1.2 features ( continued) ? parametric nand tree support for fault detection between chip i/os and the board ? loopback modes for diagnostics ? power - down and power - saving modes ? single 3.3v power supply with vdd i/o options for 1.8v, 2.5v , or 3.3v ? built - in 1.2v regulator for core ? available in 2 4 - pin (4mm 4 mm) qfn package applications ? game console ? ip phone ? ip set - top box ? ip tv ? lom ? printer ordering information ordering part number t emperature range package lead finish description ksz80 9 1rnaca 0c to 70c 24- pin qfn pb - free rmii with 25mhz crystal/clock input and 50mhz rmii ref_clk output, eee and wol support, commercial temperature . ksz80 9 1rnaia ( 1 ) ? 40c to 85c 24- pin qfn pb - free rmii with 25mhz crystal/clock input and 50mhz rmii ref_c lk output, eee and wol support, i ndustrial temperature . ksz80 9 1rndca 0c to 70c 24- pin qfn pb - free rmii normal mode with 50mhz clock input, eee and wol support, commercial temperature . ksz8091rndi a ( 1 ) ? 40c to 85c 24- pin qfn pb - free rmii normal mode with 50mhz clock input, eee and wol support, industrial temperature . ksz80 9 1rna -eval ksz80 9 1rna evaluation board (mounted with ksz8081rna device in commercial temperature) ksz80 9 1rnd -eval ksz80 9 1rnd evaluation board (mounted with ksz80 9 1rnd device in commercial temperature) note: 1. contact factory for lead time .
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 3 revision 1.2 revision history date change description/edits by: rev. 9/24/13 new datasheet. 1.0 12/2 /14 added silver wire bonding part numbers to ordering information. updated ordering information to include ordering part number and device marking. 1.1 8/ 31 /15 add max frequency for mdc in mii management (miim) interface section. updated ordering information table. updated descriptions for figure 19. add a note for figure 2 0 . updated descriptions in local loopback section for data loopback path. updated table 16. add a note for table 18. updated description and add an equation in linkmd section. add hbm esd rating in features. 1.2
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 4 revision 1.2 contents list of figures .......................................................................................................................................................................... 6 list of tables ........................................................................................................................................................................... 7 pin configuration ..................................................................................................................................................................... 8 pin description ........................................................................................................................................................................ 9 strapping options ................................................................................................................................................................. 12 functional description: 10base - t/100base - tx transceiver ................................................................................................ 13 100base - tx transmit ........................................................................................................................................................ 13 100base - tx receive ......................................................................................................................................................... 13 scrambler/de - scrambler (100base - tx only) ................................................................................................................... 13 10base - t transmit ............................................................................................................................................................ 14 10base - t receive ............................................................................................................................................................. 14 pll clock synthesizer ...................................................................................................................................................... 14 auto - n egotiation ................................................................................................................................................................ 14 rmii data interface ............................................................................................................................................................... 16 rmii signal definition ........................................................................................................................................................ 16 reference clock (ref_clk) ......................................................................................................................................... 16 tr ansmit enable (txen) ................................................................................................................................................ 16 transmit data[1:0] (txd[1:0]) ........................................................................................................................................ 16 carrier sense/receive data valid (crs_dv) ............................................................................................................... 17 receive data[1:0] (rxd[1:0]) ........................................................................................................................................ 17 receive error (rxer) .................................................................................................................................................... 17 collision detection (col) .............................................................................................................................................. 17 rmii signal diagram ? 25/50mhz clock mode ................................................................................................................. 17 rmii ? 25mhz clock mode ............................................................................................................................................ 17 rmii ? 50mhz clock mode ............................................................................................................................................ 18 back - to - back mode ? 100mbps copper repeater ............................................................................................................... 19 rmii back - to - back mode ................................................................................................................................................... 19 mii management (miim) interface ......................................................................................................................................... 20 interrupt (intrp) ................................................................................................................................................................... 20 hp auto mdi/mdi - x .............................................................................................................................................................. 21 straight cable .................................................................................................................................................................... 21 crossover cable ................................................................................................................................................................ 22 loopback mode ..................................................................................................................................................................... 22 local (digital) loopback .................................................................................................................................................... 22 remo te (analog) loopback ............................................................................................................................................... 23 linkmd ? cable diagnostic .................................................................................................................................................... 25 nand tree support .............................................................................................................................................................. 26 nand tree i/o testing ..................................................................................................................................................... 27 power management .............................................................................................................................................................. 28 power - saving mode .......................................................................................................................................................... 28 energy - detect power - down mode .................................................................................................................................... 28 power - down mode ............................................................................................................................................................ 28 slow - oscillator mode ......................................................................................................................................................... 28 energy e fficient ethernet (eee) ............................................................................................................................................ 29 transmit direction control (mac - to - phy) ........................................................................................................................ 30 receive direction control (phy - to - mac) ......................................................................................................................... 30 registers associated with eee ......................................................................................................................................... 30
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 5 revision 1.2 wake - on - lan ....................................................................................................................................................................... 31 magic - packet detection ..................................................................................................................................................... 31 customized - packet detection ........................................................................................................................................... 32 link status change detection ........................................................................................................................................... 32 reference circuit for power and ground connections ......................................................................................................... 33 typical current/power consumption .................................................................................................................................... 34 register map ......................................................................................................................................................................... 36 standard registers ............................................................................................................................................................... 38 ieee - defined registers ? descriptions ............................................................................................................................. 38 vendor - specific registers ? descriptions ......................................................................................................................... 43 mmd registers ...................................................................................................................................................................... 48 mmd register write .......................................................................................................................................................... 49 mmd register read .......................................................................................................................................................... 49 mmd regist ers ? descriptions .......................................................................................................................................... 50 absolute maximum ratings .................................................................................................................................................. 55 operating ratings ................................................................................................................................................................. 55 electrical characteristics ....................................................................................................................................................... 55 ti ming diagrams ................................................................................................................................................................... 57 rmii timing ....................................................................................................................................................................... 57 auto - negotiation timing .................................................................................................................................................... 58 mdc/mdio timing ............................................................................................................................................................ 59 power - up/reset timing .................................................................................................................................................... 60 reset circuit .......................................................................................................................................................................... 61 reference circuits ? led strap - in pin ................................................................................................................................. 62 reference clock ? connection and selection ...................................................................................................................... 63 magnetic ? connection and selection .................................................................................................................................. 64 package information and recommended land pattern ....................................................................................................... 66
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 6 revision 1.2 list of figures figure 1. auto - negotiation flow chart ................................................................................................................................ 15 figure 2. ksz8091rna/rnd rmii interface (rmii ? 25mhz clock mode) ....................................................................... 18 figure 3. ksz8091rna/rnd rmii interface (rmii ? 50mhz clock mode) ....................................................................... 18 figure 4. ksz809 1rna/rnd to ksz8091rna/rnd back - to - back copper repeater ...................................................... 19 figure 5. typical straight cable connection ...................................................................................................................... 21 figure 6. typical crossover cable connection .................................................................................................................. 22 figure 7. local (digital) loopback ...................................................................................................................................... 23 figure 8. remote (analog) loopback ................................................................................................................................. 24 figure 9. lpi mode (refresh transmissions and quiet periods) ....................................................................................... 29 figure 10. lpi transition ? rmii (100mbps) transmit .......................................................................................................... 30 figure 11. lpi transition ? rmii (100mbps) receive ........................................................................................................... 30 figure 12. ksz8091rna/rnd power and ground connectio ns ......................................................................................... 33 figure 13. rmii timing ? data received from rmii ............................................................................................................. 57 figure 14. rmii timing ? data input to rmii ........................................................................................................................ 57 figure 15. auto - negotiation fast link pulse (flp) timing .................................................................................................. 58 figure 16. mdc/mdio timing ............................................................................................................................................... 59 figure 17. power - up/reset timing ....................................................................................................................................... 60 figure 18. recommended reset circuit ............................................................................................................................... 61 figure 19. recommended reset circuit for interfacing with cpu/fpga reset output ...................................................... 61 figure 20. reference circuits for led strapping pin ........................................................................................................... 62 figure 21. 25mhz cryst al/oscillator reference clock connection ...................................................................................... 63 figure 22. 50mhz oscillator/reference clock connection .................................................................................................. 63 figure 23. typical magnetic interface circuit ........................................................................................................................ 64
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 7 revision 1.2 list of ta bles table 1. rmii signal definition ............................................................................................................................................ 16 table 2. rmii signal connection for rmii back - to - back mode (100base - tx copper repeater) ..................................... 19 table 3. mii management frame form at for the ksz8091rna/rnd ............................................................................... 20 table 4. mdi/mdi - x pin definition ...................................................................................................................................... 21 table 5. nand tree test pin order for ksz8091rna/rnd ............................................................................................. 26 table 6. ksz8091rna/rnd power pin description .......................................................................................................... 33 table 7. typical current/power consumption (vdda_3.3 = 3.3v, vddio = 3.3v) ........................................................... 34 table 8. typical current/power consumption (vdda_3.3 = 3.3v, vddio = 2.5v) ........................................................... 34 table 9. typical current/power consumption (vdda_3.3 = 3.3v, vddio = 1.8v) ........................................................... 35 table 10. standard registers supported by ksz8091rna/rnd ........................................................................................ 36 table 11. mmd registers supported by ksz8091rna/rnd .............................................................................................. 37 table 12. portal registers (access to indirect mmd registers) ........................................................................................... 48 table 13. rmii timing parameters ? ksz8091rna/rnd (25mhz input to xi pin, 50mhz output from ref_clk pin) ..... 57 table 14. rmii timing parameters ? ksz8091rna/rnd (50mhz input to xi pin) ............................................................. 57 table 15. auto - negotiation fast link pulse (flp) timing parameters ................................................................................ 58 table 16. mdc/mdio timing parameters ............................................................................................................................ 59 table 17. power - up/reset timing parameters .................................................................................................................... 60 table 18. 25mhz crystal/reference clock selection criteria .............................................................................................. 63 table 19. 50mhz oscillator/reference clock selection criteria .......................................................................................... 63 table 20. magnetics selection criteria ................................................................................................................................. 65 table 21. compatible single - port 10/100 magnetics ........................................................................................................... 65
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 8 revision 1.2 pin c onfiguration 24- pin (4mm 4mm) qfn
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 9 revision 1.2 pin description pin number pin name type ( 2 ) pin function 1 vdd_1.2 p 1.2v core vdd (power supplied by ksz8091rna/ksz8091rnd) . decouple with 2.2f and 0.1f capacitors to ground. 2 vdda_3.3 p 3.3v analog vdd . 3 rxm i/o physical receive or transmit signal ( ? differential) . 4 rxp i/o physical receive or transmit signal (+ differential) . 5 txm i/o physi cal transmit or receive signal ( ? differential) . 6 txp i/o physical transmit or receive signal (+ differential) . 7 xo o crystal feedback for 25mhz crystal . this pin is a no connect if an oscillator or external clock source is used. 8 xi i rmii ? 25mhz mode: 25mhz 50ppm crystal/oscillator/external clock input rmii ? 50mhz mode: 50mhz 50ppm oscillator/ external clock input for unmanaged mode (power - up default setting), ? ksz8091rna takes in the 25mhz crystal/clock on this pin. ? ksz8091rnd takes in the 50mhz clock on this pin. after power - up, both the ksz8091rna and ksz8091rnd can be programmed to either the 25mhz mode or 50mh z mode using phy register 1fh, bit [7]. see also ref_clk (pin 16). 9 rext i set phy transmit output current connect a 6.49k resistor to ground on this pin. 10 mdio ipu/opu mana gement interface (mii) data i/o. this pin has a weak pull - up, is open - drain, and requir es an external 1.0k pull - up resistor. 11 mdc ipu managem ent interface (mii) clock input. this clock pin is synchronous to the mdio data pin. 12 rxd1 ipd/o rmii receive data output[1] ( 3 ) . 13 rxd0 ipu/o rmii receive data output[0] ( 3 ) . 14 vddio p 3.3v, 2.5v, or 1.8v d igital v dd . notes: 2. p = power supply. gnd = ground. i = input. o = output. i/o = bi - directional. ipu = input with internal pull - up (see electrical characteristics for value). ipu/o = input with internal pull - up (see electrical characteristics f or value) during power - up/reset; output pin otherwise. ipd/o = input with internal pull - down (see electrical characteristics for value) during pow er - up/reset; output pin otherwise. ipu/opu = input with internal pull - up (see electrical characteristics for value) and output with internal pull - up (see electrical characteristics for value). 3. rmii rx mode: the rxd[1:0] bits are synchronous with the 50mhz rmii reference clock. for each clock period in which crs_dv is asserted, two bits of recovered data are sent by the phy to the mac.
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 10 revision 1.2 pin description (continued) pin number pin name type ( 2 ) pin function 15 crs_dv / phyad[1:0] ipd/o rmii mode: carrier sense/receive data valid output config mode: the pull - up/pull - down value is latched as phyad[1:0] at the de- assertion of reset. see the strapping options section for details. 16 ref_clk ipd/o rmii ? 25mhz mode: this pin provides the 50mhz rmii reference clock output to the mac. rmii ? 50mhz mode: this pin is a no connect. for unmanaged mode (power - up default setting), ? ksz8091rna is in rmii ? 25mhz mode and outputs the 50mhz rmii reference clock on this pin. ? ksz8091rnd is in rmii ? 50mhz mode and does not use this pin. after power - up, both ksz80 9 1rna and ksz80 9 1rnd can be programmed to either 25mhz mode or 50mhz mode u sing phy r egister 1fh , b it [7]. see also xi (p in 8). 17 rxer / pme_en ipd/o rmii mode: rmii receive error output config mo de: the pull - up/pull - down value is latched as pme_en at the de - assertion of reset. see the strapping options section for details. 18 intrp / pme_n2 ipu/opu interrupt output : programmable interrupt output, with register 1bh as the interrupt control/status register, for programming the interrupt conditions and reading the interrupt status. register 1fh, bit [9] sets the interrupt output to active low (default) or active high. pme_n output : programmable pme_n output (pin option 2). wh en asserted low, this pin signals that a w o l event has occurred. this pin has a weak pull - up and is an open- drain . for interrupt (when active low) and pme functions, this pin requires an external 1.0k pull - up resistor to vddio ( digital v dd ). 19 txen i rm ii transmit enable input 20 txd0 i rmii transmit data input[0 ] ( 4 ) 21 txd1 i/o rmii mode: rmii transmit data input[1] ( 4 ) nand tree mode: nand tree o utput 22 gnd gnd ground note: 4. rmii tx mode: the txd[1:0] bits are synchronous with the 50mhz rmii reference clock. for each clock period in which txen is a sserted, two bits of data are received by the phy from the mac.
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 11 revision 1.2 pin description (continued) pin number pin name type ( 2 ) pin function 23 led0 / pme_n1 / anen_speed ipu/o led output : programmable led0 output pme_n output: programmable pme_n output (pin option 1). when asserted low, this pin signals that a w o l event has occurred. in this mode, this pin has a weak pull - up, is an open - drain, and requires an external 1.0k? pull - up resistor to vddio (digital vdd). config mode : latched as auto - negotiatio n enable (register 0h, bit [12]) and speed (register 0h, bit [13]) at the de - assert ion of reset. see the strapping options section for details. the led0 pin is programmable using r egister 1fh , b its [5:4], and is defined as follows. led mode = [00] link/activity pin state led definition no link high off link low on activity toggle blinking led mode = [01] link pin state led definition no link high off link low on led mode = [10], [11] reserved 24 rst# ipu chip reset (active low) paddle gnd gnd ground
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 12 revision 1.2 strapping options pin number pin name type ( 5 ) pin function 15 phyad[1:0] ipd /o the phy address is latched at the de - assertion of reset and is configurable to either one of the following two values: pull - up = phy address is set to 00011b (3h) pull - down (default) = phy address is set to 00000b (0h) phy address 0 is assigned by default as the broadcast phy address, but it can be assigned as a unique phy address after writing a ?1? to register 16h, b it [9]. phy address bits [4:2] are set to 000 by default. 17 pme_en ipd /o pme output for wake - on - lan pull - up = enable pull - down (default) = disable at the de - assertion of reset, this pin value is latched int o r egister 16h, b it [15]. 23 anen_speed ipu/o auto - negotiation enable and speed mode pull - up (default) = enable auto- negotiation and set 100mbps speed pull - down = disable auto- negotiation and set 10mbps speed at the de - assertion of reset, this pin value is latched into r egister 0h , bit [12] for auto - negotiation enable/disable, r egister 0h , b it [13] for the speed select, and r egister 4h (auto - negotiation advertisement) for the speed capability support. note: 5. ipu/o = input with internal pull - up (see electrical characteristics for value) during power - up/reset; output pin otherwise. ipd/o = input with internal pull - down (see electrical characteristics for value) during power - up/reset; output pin otherwise. the phyad[1:0] and pme_en strap - in pins are latched at the de - assertion of reset. in some systems, the rmii mac receive input pins may drive high/low during power - up or reset, and consequently cause the phyad[1:0] and pme_en strap - in pins, shared pin with the rmii crs_dv and rxer signals respectively, to be latched to the unintended high/low state. in this case an external pull - up (4 .7k?) or pull - down (1.0k?) should be added on the phyad[1:0] and pme_en strap - in pins to ensure that the intended value is strapped - in correctly.
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 13 revision 1.2 functional description : 10base- t/100base - tx transceiver the ksz8091rna is an integrated single 3.3v supply fast ethernet transceiver. it is fully compliant with the ieee 802.3 specification, and reduces board cost and simplifies board layout by using on - chip termination resistors for the two differential pairs and by integrating the regulator to supply the 1.2v core. on the copper media side, the ksz8091rna supports 10base - t and 100base - tx for transmission and reception of data over a standard cat - 5 unshielded twisted pair (utp) cable, and hp auto mdi/mdi - x for reliable detection of and correction for straight - t hrough and crossover cables. on the mac processor side, the ksz8091rna offers the reduced media independent interface (rmii) for direct connection with rmii - compliant ethernet mac processors and switches the mii management bus option gives the mac processo r complete access to the ksz8091rna control and status registers. additionally, an interrupt pin eliminates the need for the processor to poll for phy status change. as the power - up default, the ksz8091rna uses a 25mhz crystal to generate all required cloc ks, including the 50mhz rmii reference clock output for the mac. the ksz8091rnd version uses the 50mhz rmii reference clock as the power - up default. the ksz8091rna/rnd is used to refer to both ksz8091rna and ksz8091rnd versions in this datasheet. 100base - tx transmit the 100base - tx transmit function performs parallel - to - serial conversion, 4b/5b encoding, scrambling, nrz - to - nrzi conversion, and mlt3 encoding and transmission. the circuitry starts with a parallel - to - serial conversion, which converts the rmii data from the mac into a 125mhz serial bit stream. the data and control stream is then converted into 4b/5b coding and followed by a scrambler. the serialized data is further converted from nrz - to - nrzi format, and then transmitted in mlt3 current output. t he output current is set by an external 6.49k 1% resistor for the 1:1 transformer ratio. the output signal has a typical rise/fall time of 4ns and complies with the ansi tp - pmd standard regarding amplitude balance, overshoot, and timing jitter. the wave - s haped 10base - t output is also incorporated into the 100base - tx transmitter. 100base - tx receive the 100base - tx receiver function performs adaptive equalization, dc restoration, mlt3 - to - nrzi conversion, data and clock recovery, nrzi - to - nrz conversion, de - scr ambling, 4b/5b decoding, and serial - to - parallel conversion. the receiving side starts with the equalization filter to compensate for inter - symbol interference (isi) over the twisted pair cable. because the amplitude loss and phase distortion is a function of the cable length, the equalizer must adjust its characteristics to optimize performance. in this design, the variable equalizer makes an initial estimation based on comparisons of incoming signal strength against some known cable characteristics, then t unes itself for optimization. this is an ongoing process and self - adjusts against environmental changes such as temperature variations. next, the equalized signal goes through a dc - restoration and data - conversion block. the dc - restoration circuit compensat es for the effect of baseline wander and improves the dynamic range. the differential data - conversion circuit converts mlt3 format back to nrzi. the slicing threshold is also adaptive. the clock - recovery circuit extracts the 125mhz clock from the edges of the nrzi signal. this recovered clock is then used to convert the nrzi signal to nrz format. this signal is sent through the de - scrambler, then the 4b/5b decoder. finally, the nrz serial data is converted to rmii format and provided as the input data to th e mac. scrambler/de - scrambler (100base - tx only ) the scrambler spreads the power spectrum of the transmitted signal to reduce electromagnetic interference (emi) and baseline wander. the de - scrambler recovers the scrambled signal.
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 14 revision 1.2 10ba se- t transmit the 10base - t drivers are incorporated with the 100base - tx drivers to allow for transmission using the same magnetic. the drivers perform internal wave - shaping and pre - emphasis, and output 10base - t signals with a typical amplitude of 2.5v peak for standard 10base - t mode and 1.75v peak for energy - efficient 10base - te mode . the 10base - t /10base - te signals have harmonic contents that are at least 27db below the fundamental frequency when driven by an all - ones manchester - encoded signal. 10base - t rece ive on the receive side, input buffer and level detecting squelch circuits are used. a differential input receiver circuit and a phase - locked loop (pll) performs the decoding function. the manchester - encoded data stream is separated into clock signal and nrz d ata. a squelch circuit rejects signals with levels less than 400mv, or with short pulse widths, to prevent noise at the differential line receive inputs from falsely triggering the decoder. when the input exceeds the squelch limit, the pll locks onto the i ncoming signal and the ksz8091rna/rnd decodes a data frame. the receive clock is kept active during idle periods between data receptions. pll clock synthesizer the ksz80 9 1rna/rnd in rmii ? 25mhz clock mode generates all internal clocks and all external clo cks for system timing from an external 25mhz crystal, oscillator, or reference clock. for the ksz80 9 1rna/rnd in rmii ? 50mhz clock mode, these clocks are generated from an external 50mhz oscillator or system clock. auto - negotiation the ksz80 9 1rna/rnd conforms to the auto - n egotiation protocol, defined in clause 28 of the ieee 802 .3 specification. auto - n egotiation allows unshielded twisted pair (utp) link partners to select the hi ghest common mode of operation. during auto - n egotiation, link partners adve rtise capabilities across the utp link to each other and then compare their own capabilities with those they received from their link partners. the highest speed and duplex setting that is common to the two link partners is selected as the mode of operatio n. the following list shows the speed and duplex operation mode from highest to lowest priority. ? priority 1: 100base - tx, full - duplex ? priority 2: 100base - tx, half - duplex ? priority 3: 10base - t, full - duplex ? priority 4: 10base - t, half - duplex if auto - n egot iation is not supported or the ksz80 91rna/rnd li nk partner is forced to bypass auto - n egotiation, then the ksz80 91rna/rnd sets its operating mode by observing the signal at its receiver. this is known as parallel detection, which allows the ksz80 91rna/rnd t o establish a link by listening for a fixed signal protocol in the absence of the auto - negotiation advertisement p rotocol. auto - negotiation is enabled by either hardware pin strapping (anen_speed, pin 23) or software (r egister 0h, bit [12]). by default, au to - n egotiation is enabled after power - up or hardware reset. after that, a uto - n egotiation can be enabled or disabled by register 0h, bit [12]. if auto - n egotiation is disabled, the speed is set by register 0h, b it [13], and the duplex is set by register 0h, b it [8]. the auto - n egotiation link - up process is shown in figure 1 .
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 15 revision 1.2 figure 1 . auto - negotiation flow chart
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 16 revision 1.2 rmii data interface the reduced media independent interface (rmii) specifies a low pin count media independent interface (mii). it provides a common interface between physical layer and mac layer devices, and has the following key characteristics: ? pin count is 8 pin s (3 pins for data transmission, 4 pins for data reception, and 1 pin for the 50mhz reference clock). ? 10mbps and 100mbps data rates are supported at both half - and full - duplex. ? data transmission and reception are independent and belong to separate signal groups. ? transmit data and receive data are each 2 bits wide, a dibit. rmii signal definition table 1 describes the rmii signals. refer to rmii specifi cation v1.2 for detailed information. table 1 . rmii signal definition rmii signal name direction (with respect to phy, ksz80 91rna/rnd signal) direction (with respect to mac) description ref_clk output (25mhz clock mode)/ < no connect> (50mhz clock mode) input/ input or synchronous 50mhz reference clock for receive, transmit, and control interface txen input output transmit enable txd[1:0] input output transmit data[1:0] crs_dv output input carrier sense/receive data valid rxd[1:0] output input receive data[1:0] rxer output input, or (not required) receive error reference clock (ref_clk) ref_clk is a continuous 50mhz clock that provides the timing reference for txen, txd[1:0], crs_dv, rxd[1:0], and rx_er. for rmii ? 25mhz clock mode, the ksz8091rna/rnd generates and outputs the 50mhz rmii ref_clk to the mac at ref_clk (pin 16). for rmii ? 50mhz clock mode, the ksz8091rna/rnd takes in the 50mhz rmii ref_clk from the mac or system board at xi (pin 8) and leaves the ref_clk (pin 16) as no connect. transmit enable (txen) txen indicates that the mac is presenting dibits on txd[1:0] for transmission. it is asserted synchronously with the first dibit of the preamble and remains asserted while all dibits to be transmitted are presented on the rmii. it is negated before the first ref_clk following the final dibit of a frame. txen transitions synchronously with respect to ref_clk. transmit data[1:0] (txd[1:0]) when txen is asserted, txd[1:0] are the data dib its presented by the mac and accepted by the phy for transmission. when txen is de - asserted, the mac drives txd[1:0] to either 00 for the idle state (non - eee mode) or 01 for the lpi state (eee mode). txd[1:0] transitions synchronously with respect to ref_clk.
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 17 revision 1.2 carrier sense/ receive data valid (crs_dv) the phy asserts crs_dv when the receive medium is non - idle. it is asserted asynchronously when a carrier is detected . this happens when squelch is passed in 10mbps mode, and when two non - contiguous 0s in 10 bits are detected in 100mbps mode. loss of carrier results in the de - assertion of crs_dv. while carrier detection criteria are met, crs_dv remains asserted continuously from the first recovered dibit of the frame through the final recovered dibit. it i s negated before the first ref_clk that follows the final dibit. the data on rxd[1:0] is considered valid after crs_dv is asserted. however, because the assertion of crs_dv is asynchronous relative to ref_clk, the data on rxd[1:0] is 00 until receive si gna ls are proper ly decod ed . receive data[1:0] (rxd[1:0]) f or each clock period in which crs_dv is asserted, rxd[1 :0] transfers a dibit of recovered data from the phy. when crs_dv is de - asserted, the phy drives rxd[1:0] to either 00 for the idle state (non - ee e mode) or 01 for the lpi state (eee mode). rxd[1 :0] transitions synchronously with respect to ref_clk. receive error (rxer) when crs_dv is asserted, rxer is asserted for one or more ref_clk periods to indicate that a symbol error (for example, a coding e rror that a phy can detect that may otherwise be undetectable by the mac sub - layer) i s detected somewhere in the frame that is being transferred from the phy to the mac . rxer transitions synchronously with respect to ref_clk. collision detection (col) the mac regenerates the col signal of the mii from txen and crs_dv. rmii signal diagram ? 25/50mhz clock mode the ksz80 9 1rna/rnd rmii pin connections to the mac for 25mhz clock mode are shown in figure 2 . the connections for 50mhz clock mode are shown in figure 3 . rmii ? 25mhz clock mode the ksz80 9 1rna is configured to rmii ? 25mhz clock mode after it is powered up or hardware reset with the following: ? a 25mh z crystal connected to xi, xo (p ins 8, 7), or an external 25mhz clock source (oscillator) connected to xi the ksz80 9 1rnd can optionally be configured to rmii ? 25mhz clock mode after it is powered up or hardware reset and software programmed with the following: ? a 25mh z crystal connected to xi, xo (p ins 8, 7), or an external 25mhz clock source (oscillator) connected to xi ? register 1fh, b it [7] programmed to ?1? to select rmii ? 25mhz clock mode
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 18 revision 1.2 figure 2 . ksz80 91rna/rnd rmii interface ( rmii ? 25mhz clock mode) r mii ? 5 0 mhz clock mode the ksz80 9 1rnd is configured to rmii ? 50mhz clock mode after it is powered up or hardware reset with the following: ? an external 50mhz clock source (oscillator) connected to xi (p in 8) the ksz80 9 1rna can optionally be configured to rmii ? 5 0mhz clock mode after it is powered up or hardware reset and software programmed with the following: ? an external 50mhz clock source (oscillator) connected to xi ( p in 8) ? register 1fh, b it [7] programmed to ?1? to select rmii ? 50mhz clock mode figure 3 . ksz80 91rna/rnd rmii interface ( rmii ? 50mhz clock mode)
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 19 revision 1.2 back -to- back mode ? 100mbps copper repeater two ksz80 91rna/rnd devices can be connected back - to - back to form a managed 100base - tx copper repeater. figure 4 . ksz80 91rna/rnd to ksz80 91rna/rnd back -to - back copper repeater rmii back - to - back mode in rmii back - to - back mode, a ksz80 91rna/rnd interfaces with another ksz80 91rna/rnd to provide a 100mbps copper repeater solution. t he ksz80 9 1rna/rnd devices are configured to rmii back - to - back mode after power - up or reset, and software programming, with the following: ? a common 50mhz re ference clock connected to xi (pin 8 ) of both ksz80 91rna/rnd devices . ? register 1fh, bit [7] programmed to ?1? to select rmii ? 50mhz clock mode for ksz8091rna. (ksz80 9 1rnd is set to rmii ? 50mhz clock mode as the default after power up or hardware reset) . ? register 16h, bits [6] and [1] programmed to ?1? and ?1?, respectively, to enable rmii back - to - back mode. ? rmii signals connecte d as shown in table 2 . table 2 . rmii signal connection for rmii back -to - back mode (100base- tx copper repeater) ksz80 91rna/rnd (100base - tx copper) [device 1] ksz80 91rna/rnd (100base - tx copp er) [device 2] pin name pin number pin type pin name pin number pin type crsdv 15 output txen 19 input rxd1 12 output txd1 21 input rxd0 13 output txd0 20 input txen 19 input crsdv 15 output txd1 21 input rxd1 12 output txd0 20 input rxd0 13 output
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 20 revision 1.2 mii management (miim) interface the ksz8091rna/rnd supports the ieee 802.3 mii management interface, also known as the management data input/output (mdio) interface. this interface allows an upper - layer device, such as a mac processor, to monitor and control the state of the ksz8091rna/rnd. an external device with miim capability is used to read the phy status and/or configure the phy settings. more details about the miim interface can be found in clause 22.2.4 of the ieee 802.3 specification. the miim interface consists of the following: ? a physical connection that incorporates the clock line (mdc) and the data line (mdio). ? a specific protocol that operates across the physical connection mentioned earlier, which allows the external controller to communi cate with one or more phy devices. ? a 32 - register address space for direct access to ieee - defined registers and vendor - specific registers, and for indirect access to mmd addresses and registers. see the register map section. the ksz8091rna/rnd supports only two unique phy addresses. the phyad[1:0] strapping pin is used to select either 0h or 3h as the unique phy address for the ksz8091rna/rnd device. ph y address 0h is defined as the broadcast phy address according to the ieee 802.3 specification, and can be used to read/write to a single phy device, or write to multiple phy devices simultaneously. for the ksz8091rna/rnd, phy address 0h defaults to the br oadcast phy address after power - up, but phy address 0h can be disabled as the broadcast phy address using software to assign it as a unique phy address. for applications that require two ksz8091rna/rnd phys to share the same mdio interface with one phy set to address 0h and the other phy set to address 3h, use phy address 0h (defaults to broadcast after power - up) to set both phys? register 16h, bit [9] to ?1? to assign phy address 0h as a unique (non - broadcast) phy address. the miim interface can operates u p to a maximum clock speed of 10mhz mac clock. table 3 shows the mii management frame format for the ksz80 91rna/rnd . table 3 . mii management frame format for the ksz80 91rna /rn d preamble start of frame read/write op code phy address bits [4:0] reg address bits [4:0] ta data bits [15:0] idle read 32 1?s 01 10 000aa rrrrr z0 dddddddd_dddddddd z write 32 1?s 01 01 000aa rrrrr 10 dddddddd_dddddddd z interrupt (intrp) intrp (p in 18) is an optional interrupt signal that is used to inform the external controller that there has been a status update to the ksz80 9 1rna/rnd phy r egister. bits [15:8] of r egister 1bh are the interrupt control bits to enable and disable the conditions for asserting the intrp signal. bits [7:0] of r egister 1bh are the interrupt status bits to indicate which interrupt conditions have occurred. the interrupt status bits are cle ared after reading r egister 1bh. bit [9] of r egister 1fh sets the interrupt level to active high or active low. the default is active low. the mii management bus option gives the mac processor complete access to the ksz80 9 1rna/rnd control and status regist ers. additionally, an interrupt pin eliminates the need for the processor to poll the phy for status change.
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 21 revision 1.2 hp auto mdi/mdi -x hp auto mdi/mdi - x configuration eliminates the need to decide whether to use a straight cable or a crossover cable between the ksz80 9 1rna/rnd and its link partner. this feature allows the ksz80 9 1rna/rnd to use either type of cable to connect with a link partner that is in either mdi or mdi - x mode. the auto - sense function detects transmit and receive pairs from the link partner and assigns transmit and receive pairs to the ksz80 9 1rna/rnd accordingly. hp auto mdi/mdi - x is enabled by default. it is disabled by writing a ?1? to register 1fh, b it [13]. mdi and mdi - x mode is selected by register 1fh, b it [14] if hp auto mdi/mdi - x is disa bled. an isolation transformer with symmetrical transmit and receive data paths is recommended to support auto mdi/mdi - x. table 4 shows how the ieee 80 2.3 standard defines mdi and mdi - x. table 4 . mdi/mdi - x pin definition mdi mdi -x rj - 45 pin signal rj - 45 pin signal 1 tx+ 1 rx+ 2 tx ? 2 rx ? 3 rx+ 3 tx+ 6 rx ? 6 tx ? straight cable a straight cable connects an mdi device to an mdi - x device, or an mdi - x device to an mdi device. figure 5 shows a typical straight cable connection between a nic card (mdi device) and a switch or hub (mdi - x device). figure 5 . typical straight cable connection
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 22 revision 1.2 crossover cable a crossover cable connects an mdi device to another mdi device, or an mdi - x device to another mdi - x device. figure 6 shows a typical crossover cable c onnection between two switches or hubs (two mdi - x devices). figure 6 . typical crossover cable connection loopback mode the ksz80 91rna/rnd supports the following loopback operations to verify analog and/or digital data paths. ? local (digital) loopback ? remote (analog) loopback local (digital) loopback th is loopback mode checks the rmii transmit and receive data paths between the ksz80 91rna/rnd and the external mac, and is s upported for both speeds (10/100mbps) at full - duplex. th e loopback data path is shown in figure 7 . 1. the rmii mac transmits frames to the ksz80 91rna/rnd . 2. frames are wrapped around inside the ksz80 91rna/rnd . 3. th e ksz80 91rna/rnd transmits frames back to the rmii mac. 4. except the frames back to the rmii mac , the transmit frames also go out from the copper port.
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 23 revision 1.2 figure 7 . local (digital) loopback the following programming action and register settings are used for local loopback mode. for 10/100 mbps loopback, set r egister 0h, bit [14] = 1 // enable local loopback mode bit [13] = 0/1 // select 10mbps/100mbps speed bit [12] = 0 // disable a uto - n egotiation bit [8] = 1 // select f ull - duplex mode remote (analog) loopback this loopback mode checks the line (differential pairs, transformer, rj - 45 connector, ethernet cable) transmit and receive data paths between the ksz80 91rna/rnd and its link partner, and is s upported for 100base - tx full - duplex mode only. the loopback data path is shown in figure 8 . 1. the fast ethernet (100base - tx) phy link partner transmits frames to the ksz80 91rna/rnd . 2. frames are wrapped around inside the ksz80 91rna/rnd . 3. the ksz80 91rna/rnd transmits frames back to the f ast ethernet (100base - tx) phy link partner.
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 24 revision 1.2 figure 8 . remote (analog) loopback the following programming steps and register settings are used for remote loopback mode. 1. set register 0h, bit [13] = 1 // select 100mbps speed bit [12] = 0 // disable auto - n egotiation bit [8] = 1 // selec t full - duplex mode or just auto - negotiate and link up with the link partner at 100base - tx full - duplex mode. 2. set register 1fh, bit [2] = 1 // enable remote loopback mode
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 25 revision 1.2 linkmd ? cable diagnostic the linkmd function uses time - domain reflectometry (tdr) to analyze the cabling plant for common cabling problems. these include open circuits, short circuits, and impedance mismatches. linkmd works by sending a pulse of known amplitude a nd duration down the mdi or mdi - x pair, then analyzing the shape of the reflected signal to determine the type of fault . the time duration for the reflected signal to return provides the approximate distance to the cabling fault . the linkmd function proces ses this tdr information and presents it as a numerical value that can be translated to a cable distance. li nkmd is initiated by accessing r egister 1dh, the linkmd c able diagnostic register, in conjunction with register 1fh, the phy control 2 r egister. the latter register is used to disable auto mdi/mdi - x and to select either mdi or mdi - x as the cable differential pair for testing. usage the following is a sample procedure for using linkmd with registers 1dh and 1fh: 3. disable auto mdi/mdi - x by wr iting a ?1? to register 1fh, bit [13 ] . 4. start cable diagnostic test by wr iting a ?1? to register 1dh, bit [ 15 ]. this enable bit is self - clearing. 5. wait (poll) for register 1dh , bit [ 15 ] to return a ?0?, and indicating cable diagnostic test is completed. 6. read cable diag nostic test results in register 1dh , bits [ 14: 13 ]. the results are as follows: 00 = normal condition (valid test) 01 = open condition detected in cable (valid test) 10 = short condition detected in cable (valid test) 11 = cable diagnostic test failed (invalid test) the ?11? case, invalid test, occurs when the device is unable to shut down the link partner. in this instance, the test is not run, since it would be impossible for the device to determine if the detected signal is a reflection of the signal generated or a signal from another source. 7. get distance to fault by concatenating register 1dh, bits [ 8:0 ] and multiplying the result by a constant of 0. 38 . the distance to the cable fault can be determined by the following formula: d (distance to cable fault) = 0.38 x (register 1 d h, bits [8:0]) d (distance to cable fault) is expressed in meters. concatenated value of registers 1dh bit s [ 8 :0] should be converted to decimal before multiplying by 0. 38. the constant (0. 38 ) may be calibrated for differ ent cabling conditions, including cables with a velocity of propagation that varies significantly from the norm.
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 26 revision 1.2 nand tree support the ksz80 91rna/rnd provides parametric nand tree support for fault detection between chip i/os and board. the nand tree is a chain of nested nand gates in which each ksz80 91rna/rnd digital i/o (nand tree input) pin is an input to one nand gate along the chain. at the end of the chain, the txd1 pin provides the output for the nested nand gates. the nand tree test process includ es: ? enabling nand tree mode ? pulling all nand tree input pins high ? driving each nand tree input pin low, sequentially, according to the nand tree pin order ? checking the nand tree output to make sure there is a toggle high - to - low or low - to - high for each nand tree input driven low table 5 l ist s the nand tree pin order table 5 . nand tree test pin order for ksz80 9 1rn a/rnd pin number p in name nand tree description 10 mdio input 11 mdc input 12 rxd1 input 13 rxd0 input 15 crs_dv input 16 ref_clk input 18 intrp input 19 txen input 23 led0 input 20 txd0 input 21 txd1 output
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 27 revision 1.2 nand tree i/o testing use the following procedure to check for faults on the ksz80 91rna/rnd digital i/o pin connections to the board: 1. enable nand tree mode by setting register 16h, bit [5] to ?1?. 2. use board logic to drive all ksz80 91rna/rnd nand tree input pins high. 3. use board logic to drive each nand tree input pin, in ksz80 91rna/rnd nand tree pin order, as follows: a. toggle the first pin (mdio) from high to low, and verify that the txd 1 pin switches from high to low to indicate that the first pin is connected properly. b. leave the first pin (mdio) low. c. toggle the second pin (mdc) from high to low, and verify that the txd 1 pin switches from low to high to indicate that the second pin is connected properly. d. leave the first pin (mdio) and the second pin (mdc) low. e. toggle the third pin (rxd1 ) from high to low, and verify that the txd 1 pin switches from high to low to indicate that the third pin is connected properly. f. continue with this sequence until all ksz80 91rna /rn d nand tree input pins have been toggled. each ksz80 9 1 rna/rnd nand tree input pin must cause the tx d 1 output pin to toggle high - to - low or low - to - high to indica te a good connection. if the txd1 pin fails to toggle when the ksz80 91rna/rnd input pin toggles from high to low, the input pin has a fault.
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 28 revision 1.2 power management the ksz80 91rna/rnd incorporates a number of power - management modes and features that provide methods to consume less energy. these are discussed in the following sections. power - saving mode power - saving mode is used to reduce the transceiver power consumption when the cable is unplugged. i t is enabled by writing a ?1? to register 1fh, bit [10], and is in effect when auto - n egotiation mode is enabled and the c able is disconnected (no link). in this mode, the ksz80 9 1 rna / rnd shuts down all transceiver blocks, except for the transmitter, energy detect, and pll circuits. by default, power - saving mode is disabled after power - up. energy - detect power - down mode energy - detect power - down (edpd) mode is used to further reduce transceiver power consumption when the cable is unplugged. it is enabled by wr iting a ?0? to r egister 18h, bit [11], and is in effect when auto - n egotiation mode is enabled and the cable is disconnected (no link). edpd mode works with the pll off (set by writi ng a ?1? to register 10h, b it [4] to automatically turn the pll off in edp d mode) to turn off all ksz80 91rna/rnd transceiver blocks except the transmitter and energy - detect circuits. power can be reduced further by extending the time interval between transmissions of link pulses to check for the presence of a link partner. the p eriodic transmission of link pulses is needed to ensure the ksz80 91rna/rnd and its link partner, when operating in the same low - power state and with auto mdi/mdi - x disabled, can wake up when the cable is connected between them. by default, edpd mode is disabled after power - up. power - down mode power - down mode is used to power down the ksz80 91rna/rnd device when it is not in use after power - up. it is enabled by writi ng a ?1? to register 0h, b it [11]. in this mode, the ksz80 91rna/rnd disables all internal functions except the mii management interface. the ksz80 91rna/rnd exits (d isables) power - down mode after register 0h, b it [11] is set back to ?0?. slow - oscillator mode slow - oscillator mode is used to disconnect the input reference crystal/clock on xi ( p in 8 ) and select the on - chip slow oscillator when the ksz80 91rna/rnd device is not in use after power - up. it is enabled by writing a ?1? to register 11h, b it [5]. slow - oscillator mode works in conjunction with power - down mode to put the ksz80 9 1 rna/rn d device in the lowest power state , with all internal functions disabled except the mii management interface. to properly exit this mode and return to normal phy operation, use the following programming sequence: 1. disable slow - oscillator mode by writing a ? 0? to r egister 11h, b it [5]. 2. disable power - down mode by writing a ?0? to register 0h, b it [11]. 3. initiate soft ware reset by writing a ?1? to register 0h, b it [15].
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 29 revision 1.2 energy efficient ethernet (eee) the ksz8091rna/rnd implements energy efficient ethernet (e ee) a s described in the ieee standard 802.3az for 100base - tx copper signaling by the two differential pairs (analog side) and according to the multisource agreement (msa) of collaborating fast ethernet chip vendors for the r mii (digital side). the msa agreement is based on the ieee standard?s eee implementation for the 100mbps m edia independent interface ( mii ). the ieee s tandard is defined around a n eee - compliant mac on the host side and an eee - compliant link partner on the line side that support speci al signaling associated with eee. eee saves power by keeping the ac signal on the copper ethernet cable at approximately 0v peak - to - peak as often as possible during periods of no traffic activity, while maintaining the link - up status. this is referred to a s low - p ower idle (lpi) mode or state . during lpi mode, the copper link respond s automatically when it receives traffic and resumes normal phy operation immediately, without blockage of traffic or loss of packet. this involves exiting lpi mode and returnin g to normal 100mbps operating mode. wake - up time is <30 s for 100b ase - t x. the lpi state is controlled independently for transmit and receive paths, allowing the lpi state to be active (enabled) for: ? transmit cable path only ? receive cable path only ? both tr ansmit and receive cable paths the ksz 8091rna/rnd has the eee function disabled as the power - up default setting. to enable the eee function for 100mbps mode, use the following programming sequence: 1. enable 100mbps eee mode advertisement by writing a ?1? to mmd address 7h, register 3ch, bit [1]. 2. restart auto - negotiation by writing a ?1? to standard register 0h, bit [9]. for standard (non - eee) 10base - t mode, normal link pulses (nlps) with long periods of no ac signal transmission are used to maintain the link during the idle period when there is no traffic activity. to save more power, the ksz 8091rna/rnd provides the option to enable 10base - te mode, which saves additional power by reducing the transmitted signal amplitude from 2.5v to 1.75v. to enable 10ba se - te mode, write a ?1? to standard register 13h, b it [ 4 ] and write a ?0? to mmd address 1ch, register 4h, bit [13]. during lpi mode, refresh transmissions are used to maintain the link; power savings occur in quiet periods. approximately every 20 ms to 22m s, a refresh transmission of 200 s to 220 s is sent to the link partner. the refresh transmissions and quiet periods are shown in figure 9 . figure 9 . lpi mode (refresh transmissions and quiet periods)
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 30 revision 1.2 transmit direction control (mac - to - phy) the ksz8091rna/rnd enters lpi mode for the transmit direct ion when its attached eee - compliant rmii mac de - asserts txen and sets txd[1:0] to 01. the ksz8091rna/rnd remain s in the lpi transmit state while the rmii mac maintains the states of these signals. whe n the rmii mac changes any of the txen or tx data signal s from the ir lpi state values, the ksz8091rna/rnd exit s the lpi transmit state. figure 10 shows the lpi transition for rmii (100mbps) transmi t. figure 10 . lpi transition ? rmii (100mbps) transmit receive direction control (phy - to - mac) the ksz8091rna/rn d enters lpi mode for the receive direction when it receives the /p/ code bit pattern (sleep/refresh) from its eee - compliant link partner. it then de - asserts crs_dv and drives rxd[1:0] to 01. the ksz 8091rna/rnd remains in the lpi receive state while it con tinues to receive the refresh from its link partner, so it will continue to maintain and drive the lpi output states for the rmii receive signals to inform the attached eee - compliant rmii mac that it is in the lpi receive state. when the ksz8091 rna/rnd rec eives a non /p/ code bit pattern (non - refresh), it exits the lpi receive state and sets the crs_dv and rx data signals to set a normal frame or normal idle. figure 11 shows the lpi transition for rmii (100mbps) receive . figure 11 . lpi transition ? rmii (100mbps) receive registers associated with eee the following registers are provided for eee configuration and management: ? standard register 13h ? afe control 4 (to enable 10base - te mode) ? mmd a ddress 1h, r egister 0h ? p ma/pmd control 1 (to enable lpi) ? mmd a ddress 1h, register 1 h ? p ma/pmd status 1 (for lpi status) ? mmd address 7h, r egister 3ch ? eee advertisement ? mmd address 7 h, r egister 3dh ? eee link partner advertisement ? mmd address 1ch, register 4h ? dsp 10base - t/10base - te control
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 31 revision 1.2 wake -o n- lan wake - on - lan (wol) is normally a mac - based function to wake up a host system (for example, an ethernet end device, such as a pc) that is in standby power mode. wake - up is triggered by receiving and detecting a special packet (commonly referred to as the ?magic packet?) that is sent by the remote link partner. the ksz 8091rna/rnd can perform the same w o l function if the mac address of its associated mac device is entered into the ksz 8091rna/rnd phy r egisters for magic - packet detection. when the ksz 8091rna/rnd detects the magic packet, it wakes up the host by driving its power management event (pme) output pin low. by default, the w o l function is disabled. it is enabled by setting the enabling bit and configuring the associated registers for the selected pme wake - up detection me thod. the ksz 8091rna/rnd provides three methods to trigger a pme wake - up: ? magic - packet detection ? customized - packet detection ? link status change detection magic - packet detection the magic packet?s frame format starts with 6 bytes of 0xffh and is followed b y 16 repetitions of the mac address of its associated mac device (local mac device). when the magic packet is detected from its link partner, the ksz 8091rna/rnd asserts its pme output pin low. the following mmd a ddress 1fh registers are provided for magic - packet detection: ? magic - packet detection is enabled by wri ting a ?1? to mmd address 1fh, register 0h, b it [6] ? the mac address (for the local mac device) i s written to and stored in mmd a ddress 1fh, r egisters 19h ? 1bh the ksz 8091rna/rnd does not generate the magic packet. the magic packet must be provided by the external system.
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 32 revision 1.2 customized - packet detection the customized packet has associated register/bit masks to select which byte, or bytes, of the first 64 bytes of the packet to use in the crc calculatio n. after the ksz 8091rna/rnd receives the packet from its link partner, the selected bytes for the received packet are used to calculate the crc. the calculated crc is compared to the expected crc value that was previously written to and stored in the ksz 80 91rna/rnd phy r egisters. if there is a match, the ksz 8091rna/rnd asserts its pme output pin low. four customized packets are provided to support four types of wake - up scenarios. a dedicated set of registers is used to configure and enable each customized p acket. the following mmd r egisters are provided for customized - packet detection: ? each of the four customized packets i s enabled via mmd address 1fh, r egister 0h, bit [2] // for customized packets, type 0 bit [3] // for customized packets, type 1 bit [4] // for customized packets, type 2 bit [5] // for customized packets, type 3 ? masks to indicate which of the first 64 - bytes to use in the crc calculation are set in: mmd address 1fh, r egisters 1h ? 4h // for customized packets, type 0 mmd address 1fh, re gis ters 7h ? ah // for customized packets, type 1 mmd address 1fh, r egisters dh ? 10h // for customized packets, type 2 mmd address 1fh, r egisters 13h ? 16h // for customized packets, type 3 ? 32- bit expected crcs are written to and stored in: mmd address 1fh, r egisters 5h ? 6h // for customized packets, type 0 mmd address 1fh, r egisters bh ? ch // for customized packets, type 1 mmd address 1fh, r egisters 11h ? 12h // for customized packets, type 2 mmd address 1fh, r egisters 17h ? 18h // for customized packets, type 3 link status change detection if link status change detection is enabled, the ksz 8091rna/rnd asserts its pme output pin low whenever there is a link status c hange, using the following mmd a ddress 1fh register bits and their enabled (1) or disabled ( 0) settings: ? mmd address 1fh, register 0h, b it [0] // for link - up detection ? mmd address 1fh, register 0h, b it [1] // for link - down detection the pme output signal is ava ilable on either intrp/pme_n2 (pin 1 8) or led0/pme_n1 (p in 23 ), and is enabled using standard register 16h, bit [15]. mmd a dd ress 1fh, register 0h, b its [15:14] defines and selects the output functions for pins 1 8 and 23. the pme output is active low and requires a 1k pull - up to the vddio supply. when asserted, the pme output is cleared b y disabling the register bit that enabled the pme trigger source (magic packet, customized packet, link status change).
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 33 revision 1.2 reference circuit for power and ground connections the ksz80 9 1 rna/rnd is a single 3.3v supply device with a built - in regulator to supp ly the 1.2v core. the power and ground connections are shown in figure 12 and table 6 for 3.3v vddio. figure 12 . ksz80 91rna/rnd power and ground connections table 6 . ksz80 91rna/rnd power pin description power pin pin number description vdd_1.2 1 decouple with 2.2f and 0.1f capacitors to ground. vdda_3.3 2 connect to board?s 3.3v supply through a ferrite bead. decouple with 22f and 0.1f capacitors to ground. vddio 14 connect to board?s 3.3v supply for 3.3v vddio. decouple with 22f and 0.1f capacitors to ground.
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 34 revision 1.2 typical current/power consumption table 7 , table 8 , and table 9 show typical values for current consumption by the transceiver (vdda_3.3) and digital i/o (vddio) power pins , and typical values for power consumption by the ksz80 91rna/rnd device for the indicated nominal operating voltages. these current and power consumption values include the transmit driver current and on - chip regul ator cu rrent for the 1.2v core. table 7 . typical current/power consumption (vdda_3.3 = 3.3v, vddio = 3.3v) transceiver (3.3v), digital i/os (3.3v) condition 3.3v transceiver (vdda_3.3) 3.3v digital i/os (vddio) total chip power ma ma mw 100base - tx link - up (no traffic) 34 12 152 100base - tx full - duplex @ 100% utilization 34 13 155 10base - t link - up (no traffic) 14 11 82.5 10base - t full - duplex @ 100% utilization 30 11 135 eee 100mbps link - up mode (transmit and receive in lpi state with no traffic) 13 10 75.9 power - saving mode (reg. 1fh, b it [10] = 1) 1 3 10 7 5.9 edpd mode (reg. 18h, b it [11] = 0) 10 10 66.0 edpd mode (reg. 18h, b it [1 1] = 0) and pll off (reg. 10h, b it [4] = 1) 3.77 1.54 17.5 soft ware power - down mode (reg. 0h, b it [11] =1) 2.59 1.51 13.5 soft ware power - down mode (reg. 0h, b it [11] =1) and s low - oscillator mode (reg. 11h, b it [5] =1) 1.36 0.45 5.97 table 8 . typical current/power consumption (vdda_3.3 = 3.3v, vddio = 2.5v) transceiver (3.3v), digital i/os (2.5v) condition 3.3v transceiver (vdda_3.3) 2.5v digital i/os (vddio) total chip power ma ma mw 100base - tx link - up (no traffic) 34 11 140 100base - tx full - duplex @ 100% utilization 34 12 142 10base - t link - up (no traffic) 15 10 74.5 10base - t full - duplex @ 100% utilization 27 10 114 eee 100mbps link - up mode (transmit and receive in lpi state with no traffic) 13 10 67.9 power - saving mode (reg. 1fh, b it [10] = 1) 1 3 10 67.9 edpd mode (reg. 18h, b it [11] = 0) 11 10 61.3 edpd mode (reg. 18h, b it [1 1] = 0) and pll off (reg. 10h, b it [4] = 1) 3.55 1.35 15.1 soft ware power - down mode (reg. 0h, b it [11] =1) 2.29 1.34 10.9 soft ware power - down mode (reg. 0h, b it [11] =1) and s low - oscillator mode (reg. 11h, b it [5] =1) 1.15 0.29 4.52
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 35 revision 1.2 table 9 . typical current/power consumption (vdda_3.3 = 3.3v, vddio = 1.8v) transceiver (3.3v), digital i/os (1.8v) condition 3.3v transceiver (vdda_3.3) 1.8v digital i/os (vddio) total chip power ma ma mw 100base - tx link - up (no traffic) 34 11 132 100base - tx full - duplex @ 100% utilization 34 12 134 10base - t link - up (no traffic) 15 9.0 65.7 10base - t full - duplex @ 100% utilization 27 9.0 105 eee 100mbps link - up mode (transmit and receive in lpi state with no traffic) 13 9.0 59.1 power - saving mode (reg. 1fh, b it [10] = 1) 13 9.0 59.1 edpd mode (reg. 18h , b it [11] = 0) 11 9.0 52.5 edpd mode (reg. 18h, b it [1 1] = 0) and pll off (reg. 10h, b it [4] = 1) 4.05 1.21 15.5 soft ware power - down mode (reg. 0h, b it [11] =1) 2.79 1.21 11.4 soft ware power - down mode (reg. 0h, b it [11] =1) and slow - oscillator mode (re g. 11h, b it [5] =1) 1.65 0.19 5.79
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 36 revision 1.2 register map the register space within t he ksz8091rna/rnd consists of two distinct areas. ? standard registers : // direct register access ? mdio manageable device (mmd) registers : // indirect register access the ksz8091rna/rnd supports the following standard registers: table 10. standard r egisters supported by ksz8091rna /rn d register number (hex) desc ription ieee - defined registers 0h basic control 1h basic status 2h phy identifier 1 3h phy identifier 2 4h auto - negotiation advertisement 5h auto - negotiation link partner ability 6h auto - negotiation expansion 7h auto - negotiation next page 8h auto - negotiation link partner next page ability 9 h ? ch reserved dh mmd access ? control eh mmd access ? register/data fh reserved vendor - specific registers 10h digital reserved control 11h afe control 1 12h reserved 13h afe control 4 14h reserved 15h rxer counter 16h operation mode strap override 17h operation mode strap status 18h expanded control 1 9 h ? 1ah reserved 1bh interrupt control/status 1ch reserved 1dh linkmd cable diagnostic 1eh phy control 1 1fh phy control 2
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 37 revision 1.2 the ksz 8091rna/rnd supports the following mmd device addresses and their associated register addresses, which mak e up the indirect mmd registers: table 11. mmd r egisters supported by ksz8091rna /rn d device address (hex) register addres s (hex) description 1h 0h pma/pmd control 1 1h pma/pmd status 1 7h 3ch eee advertisement 3dh eee link partner advertisement 1ch 4h dsp 10base - t/10base- te control 1f h 0h wake - on - lan ? control 1h wake - on - lan ? customized packet, type 0, mask 0 2h wake - on - lan ? customized packet, type 0, mask 1 3h wake - on - lan ? customized packet, type 0, mask 2 4h wake - on - lan ? customized packet, type 0, mask 3 5h wake - on - lan ? customized packet, type 0, expected crc 0 6h wake - on - lan ? customized packet, type 0, expected crc 1 7h wake - on - lan ? customized packet, type 1, mask 0 8h wake - on - lan ? customized packet, type 1, mask 1 9h wake - on - lan ? customized packet, type 1, mask 2 ah wake - on - lan ? customized packet, type 1, mask 3 bh wake - on - lan ? customized packet, type 1, expected crc 0 ch wake - on - lan ? customized packet, type 1, expected crc 1 dh wake - on - lan ? customized packet, type 2, mask 0 eh wake - on - lan ? customized packet, type 2, mask 1 fh wake - on - lan ? customized packet, type 2, mask 2 10h wake - on - lan ? customized packet, type 2, mask 3 11h wake - on - lan ? customized packet, type 2, expected crc 0 12h wake - on - lan ? customized packet, type 2, expected crc 1 13h wake - on - lan ? customized packet, type 3, mask 0 14h wake - on - lan ? customized packet, type 3, mask 1 15h wake - on - lan ? customized packet, type 3, mask 2 16h wake - on - lan ? customized packet, type 3, mask 3 17h wake - on - lan ? customized packet, type 3, expected crc 0 18h wake - on - lan ? customized packet, type 3, expected crc 1 19h wake - on - lan ? magic packet, mac -da -0 1ah wake - on - lan ? magic packet, mac -da -1 1bh wake - on - lan ? magic packet, mac -da -2
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 38 revision 1.2 standard r egister s standard registers provide direct read/write access to a 32 - register address space, as defined in clause 22 of the ieee 802.3 specification. within this address space, the first 16 registers (r egisters 0h to fh) are defined according to the ieee specific ation, while the remaining 16 registers ( r egisters 10h to 1fh) are defined specific to the phy vendor. ieee - defined registers ? descriptions address name description mode ( 6 ) default register 0h ? basic control 0.15 reset 1 = software reset 0 = normal operation this bit is self - cleared after a ?1? is written to it. rw/sc 0 0.14 loopback 1 = loopback mode 0 = normal operation rw 0 0.13 speed select 1 = 100mbps 0 = 10mbps this bit is ignored i f auto - negotiation is enabled (r egister 0.12 = 1). rw set by the anen_ speed strapping pin . see the strapping options section for details. 0.12 auto - negotiation enable 1 = en able auto -n egotiation process 0 = disable auto -n egotiation process if enabled, the auto -n egotiation result overrides the settings in r egisters 0.13 and 0.8. rw set by the a nen _speed strapping pin. see the strapping options section for details. 0.11 power - down 1 = power - down mode 0 = normal operation if software reset ( r egister 0.15) is used to exit power - down mode ( r egister 0.11 = 1), two software reset writes ( r egister 0.15 = 1) are required. the first write clears power - down mode; the second write resets the chip and re - latches the pin strapping pin values. rw 0 0.10 isolate 1 = elec trical isolation of phy from rmii 0 = normal operation rw 0 0.9 restart auto - negotiation 1 = restart auto -n egotiation process 0 = normal operation. this bit is self - cleared after a ?1? is written to it. rw/sc 0 0.8 duplex mode 1 = full - duplex 0 = half - duplex rw 1 0.7 collision test 1 = enable col test 0 = disable col test rw 0 0.6:0 reserved reserved ro 000_0000 note: 6. rw = read/write. ro = read only. sc = self - cleared. lh = latch high. ll = latch low.
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 39 revision 1.2 ieee - defined registers ? descriptions (continued) address name description mode ( 6 ) default register 1h ? basic status 1.15 100base -t4 1 = t4 capable 0 = not t4 capable ro 0 1.14 100base - tx full - duplex 1 = capable of 100mbps full - duplex 0 = not capable of 100mbps full - duplex ro 1 1.13 100base - tx half - duplex 1 = capable of 100mbps half - duplex 0 = not capable of 100mbps half - duplex ro 1 1.12 10base -t full - duplex 1 = capable of 10mbps full - duplex 0 = not capable of 10mbps full - duplex ro 1 1.11 10base -t half - duplex 1 = capable of 10mbps half - duplex 0 = not capable of 10mbps half - duplex ro 1 1.10:7 reserved reserved ro 000_0 1.6 no preamble 1 = preamble suppression 0 = normal preamble ro 1 1.5 auto - negotiation complete 1 = auto -n egotiation process completed 0 = auto -n egotiation process not completed ro 0 1.4 remote fault 1 = remote fault 0 = no remote fault ro/lh 0 1.3 auto - negotiation ability 1 = can perform auto -n egotiation 0 = cannot perform auto -n egotiation ro 1 1.2 link status 1 = link is up 0 = link is down ro/ll 0 1.1 jabber detect 1 = jabber detected 0 = jabber not detected (default is low) ro/lh 0 1.0 extended capability 1 = supports extended capability registers ro 1 register 2h ? phy identifier 1 2.15:0 phy id number assigned to the 3rd through 18th bits of the organizationally unique identifier (oui). kendin communication?s oui is 0010a1 (hex). ro 0022h register 3h ? phy identifier 2 3.15:10 phy id number assigned to the 19th through 24th bits of the organizationally unique identifier (oui). kendin communication?s oui is 0010a1 (hex). ro 0001_01 3.9:4 model number six - bit manufacturer?s model number ro 01_0110 3.3:0 revision number four - bit manufacturer?s revision number ro indicates silicon revision
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 40 revision 1.2 ieee - defined registers ? descriptions (continued) address name description mode ( 6 ) default register 4h ? auto - negotiation advertisement 4.15 next page 1 = next page capable 0 = no next page capability rw 0 4.14 reserved reserved ro 0 4.13 remote fault 1 = remote fault supported 0 = no remote fault rw 0 4.12 reserved reserved ro 0 4.11:10 pause [00] = no pause [10] = asymmetric pause [01] = symmetric pause [11] = asymmetric and symmetric pause rw 00 4.9 100base -t4 1 = t4 capable 0 = no t4 capability ro 0 4.8 100base - tx full - duplex 1 = 100mbps full - duplex capable 0 = no 100mbps full - duplex capability rw set by the anen_ speed strapping pin . see the strapping options section for details. 4.7 100base - tx half - duplex 1 = 100mbps half - duplex capable 0 = no 100mbps half - duplex capability rw set by the anen_ speed strapping pin . see the strapping options section for details. 4.6 10base -t full - duplex 1 = 10mbps full - duplex capable 0 = no 10mbps full - duplex capability rw 1 4.5 10base -t half - duplex 1 = 10mbps half - duplex capable 0 = no 10mbps half - duplex capability rw 1 4.4:0 selector field [00001] = ieee 802.3 rw 0_0001 register 5h ? auto - negotiation link partner ability 5.15 next page 1 = next page capable 0 = no next page capability ro 0 5.14 acknowledge 1 = link code word received from partner 0 = link code word not yet received ro 0 5.13 remote fault 1 = remote fault detected 0 = no remote fault ro 0 5.12 reserved reserved ro 0 5.11:10 pause [00] = no pause [10] = asymmetric pause [01] = symmetric pause [11] = asymmetric and symmetric pause ro 00 5.9 100base -t4 1 = t4 capable 0 = no t4 capability ro 0
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 41 revision 1.2 ieee - defined registers ? descriptions (continued) address name description mode (6) default 5.8 100base - tx full - duplex 1 = 100mbps full - duplex capable 0 = no 100mbps full - duplex capability ro 0 5.7 100base - tx half - duplex 1 = 100mbps half - duplex capable 0 = no 100mbps half - duplex capability ro 0 5.6 10base -t full - duplex 1 = 10mbps full - duplex capable 0 = no 10mbps full - duplex capability ro 0 5.5 10base -t half - duplex 1 = 10mbps half - duplex capable 0 = no 10mbps half - duplex capability ro 0 5.4:0 selector field [00001] = ieee 802.3 ro 0_0001 register 6h ? auto - negotiation expansion 6.15:5 reserved reserved ro 0000_0000_000 6.4 parallel detection fault 1 = fault detected by parallel detection 0 = no fault detected by parallel detection ro/lh 0 6.3 link partner next page able 1 = link partner has next page capability 0 = link p artner does not have next page capability ro 0 6.2 next page able 1 = local device has next page capability 0 = local device does not have next page capability ro 1 6.1 page received 1 = new page received 0 = new page not received yet ro/lh 0 6.0 link partner auto - negotiation able 1 = link partner has auto -n egotiation capability 0 = link partner does not have auto - negotiation capability ro 0 register 7h ? auto - negotiation next page 7.15 next page 1 = additional next pages will follow 0 = last page rw 0 7.14 reserved reserved ro 0 7.13 message page 1 = message page 0 = unformatted page rw 1 7.12 acknowledge2 1 = will comply with message 0 = cannot comply with message rw 0 7.11 toggle 1 = previous value of transmitted link code word equal to logic 0 0 = previous value of transmitted link code word equal to logic 1 ro 0 7.10:0 message field 11- bit wide field to encode 2048 messages rw 000_0000_0001
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 42 revision 1.2 ieee - defined registers ? descriptions (continued) address name description mode (6) default register 8h ? auto - negotiation link partner next page ability 8.15 next page 1 = additional next pages will follow 0 = last page ro 0 8.14 acknowledge 1 = successful receipt of link word 0 = no successful receipt of link word ro 0 8.13 message page 1 = message page 0 = unformatted page ro 0 8.12 acknowledge2 1 = can act on the information 0 = cannot act on the information ro 0 8.11 toggle 1 = previous value of transmitted link code word equal to logic 0 0 = previous value of transmitted link code word equal to logic 1 ro 0 8.10:0 message field 11- bit wide field to encode 2048 messages ro 000_0000_0000 register dh ? mmd access ? control d.15:14 mmd ? operation mode for th e selected mmd device address (b its [4:0] of this register), these two bits select one of the following register or data operations and the usage for mmd access ? register/data (reg. eh). 00 = register 01 = data, no post increment 10 = data, post increment on reads and writes 11 = data, post increment on writes only rw 00 d.13:5 reserved reserved rw 00_0000_000 d.4:0 mmd ? device address these five bits set the mmd device address. rw 0_0000 register eh ? mmd access ? register/data e.15:0 mmd ? register/data for the selecte d mmd device address (reg. dh, b its [4:0]), when reg. dh, b its [15:14] = 00, this register contains the read/writ e register address for the mmd d evice a ddress . otherwise, this register contains the rea d/write dat a value for the mmd d evice a ddress and its selected register address. see also reg. dh, b its [15:14], for descriptions of post increment reads and writes of this register for data operation. rw 0000_0000_0000_0000
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 43 revision 1.2 vendor - specific registers ? descriptions address name description mode (7) default register 10h ? digital reserved control 10.15:5 reserved reserved rw 0000_0000_000 10.4 pll off 1 = turn pll off automatically in edpd mode 0 = keep pll on in edpd mode. see also register 18h, b it [11] for edpd mode rw 0 10.3:0 reserved reserved rw 0000 register 11h ? afe control 1 11.15:6 reserved reserved rw 0000_0000_00 11.5 slow - oscillator mode enable slow - oscillator mode is used to disconnect the input reference crystal/clock on the xi pin and select the on - chip slow oscillator when the ksz80 91rna/rnd device is not in use after power -up. 1 = enable 0 = disable this bit automatically sets software power - down to the analog side when enabled. rw 0 11.4:0 reserved reserved rw 0_0000 register 13 h ? afe control 4 13 .15: 5 reserved reserved rw 0000_ 000 0 _000 13. 4 10base - te mode 1 = eee 10base - te (1.75v tx amplitude) and also set mmd address 1ch, register 4h, bit [13] to ?0?. 0 = standard 10base - t (2.5v tx amplitude) and also set mmd address 1ch, register 4h, bit [13] to ?1?. rw 0 13.3:0 reserved reserved rw 0000 register 15h ? rxer counter 15.15:0 rxer counter receive error counter for symbol error frames ro/sc 0000h register 16h ? operation mode strap override 16.15 pme enable pme for wake - on - lan 1 = enable 0 = disable this bit works i n conjunction with mmd address 1fh, reg. 0h, bits [15:14] to define the output f or pins 18 and 23. rw set by the pme_en strapping pin. see the strapping options section for details. 16.14 :11 reserved reserved rw 000_0 16.10 reserved reserved ro 0 16.9 b- cast_off override 1 = override to disable broadcast (default setting) for phy address 0 if bit is ?1?, phy address 0 is non - broadcast. rw 0 16.8 :7 reserved reserved rw 0 _0 note: 7. rw = read/write. ro = read only. sc = self - cleared.
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 44 revision 1.2 vendor - specific registers ? descriptions (continued) address name description mode ( 7 ) default 16.6 rmii b -to -b override 1 = override to enable rmii back - to - back mode (also set bit 1 of this register to ?1?) rw 0 16.5 nand tree override 1 = override to enable nand t ree mode rw 0 16.4:2 reserved reserved rw 0_00 16.1 rmii override 1 = override to enable rmii mode rw 1 16.0 reserved reserved rw 0 register 17h ? operation mode strap status 17.15 reserved reserved ro 17.14 :13 phyad[1 :0] strap - in status [ 00] = strap to phy addres s 00000b (0 h) [11] = strap to phy address 00011b ( 3h) the ksz8091rna/rnd supports phy addresses 0h and 3h only. ro set by the phyad[1:0] strapping pin. see the strapping options section for details. 17.12:2 reserved reserved ro 17.1 rmii strap - in status 1 = strap to rmii mode ro 17.0 reserved reserved ro register 18h ? expanded control 18.15:12 reserved reserved rw 0000 18.11 edpd disabled energy - detect power - down mode 1 = disable 0 = enable see also r e gister 10h, b it [4] for pll off. rw 1 18.10 :0 reserved reserved rw 000_00 00_000 1 register 1bh ? interrupt control/status 1b.15 jabber interrupt enable 1 = enable jabber interrupt 0 = disable jabber interrupt rw 0 1b.14 receive error interrupt enable 1 = enable receive error interrupt 0 = disable receive error interrupt rw 0 1b.13 page received interrupt enable 1 = enable page received interrupt 0 = disable page received interrupt rw 0 1b.12 parallel detect fault interrupt enable 1 = enable parallel detect fault interrupt 0 = disable parallel detect fault interrupt rw 0 1b.11 link partner acknowledge interrupt enable 1 = enable link partner acknowledge interrupt 0 = di sable link partner acknowledge interrupt rw 0 1b.10 link - down interrupt enable 1= enable link - down interrupt 0 = disable link - down interrupt rw 0
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 45 revision 1.2 vendor - specific registers ? descriptions (continued) address name description mode ( 7 ) default 1b.9 remote fault interrupt enable 1 = enable remote fault interrupt 0 = disable remote fault interrupt rw 0 1b.8 link - up interrupt enable 1 = enable link - up interrupt 0 = disable link - up interrupt rw 0 1b.7 jabber interrupt 1 = jabber occurred 0 = jabber did not occur ro/sc 0 1b.6 receive error interrupt 1 = receive error occurred 0 = receive error did not occur ro/sc 0 1b.5 page receive interrupt 1 = page receive occurred 0 = page receive did not occur ro/sc 0 1b.4 parallel detect fault interrupt 1 = parallel detect fault occurred 0 = parallel detect fault did not occur ro/sc 0 1b.3 link partner acknowledge interrupt 1 = link partner acknowledge occurred 0 = link partner acknowledge did not occur ro/sc 0 1b.2 link - down interrupt 1 = link - down occurred 0 = link - down did not occur ro/sc 0 1b.1 remote fault interrupt 1 = remote fault occurred 0 = remote fault did not occur ro/sc 0 1b.0 link - up interrupt 1 = link - up occurred 0 = link - up did not occur ro/sc 0 register 1dh ? linkmd c able diagnostic 1d.15 cable diagnostic test enable 1 = enable cab le diagnostic test. after test has completed, this bit is self - cleared. 0 = indicates cabl e diagnostic test (if enabled) has comple ted and the status information is valid for read. rw/sc 0 1d.14:13 cable diagnostic test result [00] = normal condition [01] = open condition has been detected in c able [10] = short condition has been detected in cable [11] = cable diagnostic test has failed ro 00 1d.12 short cable short indicator 1 = a s hort cable (<10 meter) short condition has been detected by linkmd ro 0 1d.11:9 reserved reserved rw 000 1d.8:0 cable fault counter distance to fault ro 0_0000_0000
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 46 revision 1.2 vendor - specific registers ? descriptions (continued) address name description mode ( 7 ) default register 1eh ? phy control 1 1e.15:10 reserved reserved ro 0000_00 1e.9 enable pause (flow control) 1 = flow control capable 0 = no flow control capability ro 0 1e.8 link status 1 = link is up 0 = link is down ro 0 1e.7 polarity status 1 = polarity is reversed 0 = polarity is not reversed ro 1e.6 reserved reserved ro 0 1e.5 mdi/mdi - x state 1 = mdi - x 0 = mdi ro 1e.4 energy detect 1 = signal p resent on receive differential pair 0 = no signal de tected on receive differential pair ro 0 1e.3 phy isolate 1 = phy in isolate mode 0 = phy in normal operation rw 0 1e.2:0 operation mode indication [000] = still in auto -n egotiation [001] = 10base - t half - duplex [010] = 100base - tx half - duplex [011] = reserved [100] = reserved [101] = 10base - t full - duplex [110] = 100base - tx full - duplex [111] = reserved ro 000 register 1fh ? phy control 2 1f.15 hp_mdix 1 = hp auto mdi/mdi - x mode 0 = micrel auto mdi/mdi - x mode rw 1 1f.14 mdi/mdi - x select when auto mdi/mdi - x is disabled, 1 = mdi - x mode trans mit on rxp,rxm (pins 4, 3) and receive on txp,txm (pins 6, 5 ) 0 = mdi mode tran smit on txp,txm (pins 6, 5) and receive on rxp,rxm (pins 4, 3 ) rw 0 1f.13 pair swap disable 1 = disable auto mdi/mdi - x 0 = enable auto mdi/mdi - x rw 0 1f.12 reserved reserved rw 0
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 47 revision 1.2 vendor - specific registers ? descriptions (continued) address name description mode ( 7 ) default 1f.11 force link 1 = force link pass 0 = normal link operation this bit bypasses the control logic and allows the transmitter to send a pattern even if there is no link. rw 0 1f.10 power saving 1 = enable power saving 0 = disable power saving rw 0 1f.9 interrupt level 1 = interrupt pin active high 0 = interrupt pin active low rw 0 1f.8 enable jabber 1 = enable jabber counter 0 = disable jabber counter rw 1 1f.7 rmii reference clock select 1 = f or ksz8091rna, clock input to xi (pin 8) is 50mhz for rmii ? 50mhz clock mode. for ksz8091rnd, clock input to xi (pin 8) is 25mhz for rmii ? 25mhz clock mode. 0 = f or ksz8091rna, clock input to xi (pin 8) is 25mhz for rmii ? 25mhz clock mode. for ksz8091rnd, clock input to xi (pin 8) is 50mhz for rmii ? 50mhz clock mode. rw 0 1f.6 reserved reserved rw 0 1f.5:4 led mode [00] = led0: link/activity [01] = led0: link [10], [11] = reserved rw 00 1f.3 disable transmitter 1 = disable transmitter 0 = enable transmitter rw 0 1f.2 remote loopback 1 = remote (analog) loopback is enabled 0 = normal mode rw 0 1f.1 reserved reserved rw 0 1f.0 disable data scrambling 1 = disable scrambler 0 = enable scrambler rw 0
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 48 revision 1.2 mmd r egister s mmd registers provide indirect read/write access to up to 32 mmd device addresses with each device supporting up to 65,536 16 - bit registers, as defined in clause 22 of the ieee 802.3 specification. the ksz8091rna/rnd , however, uses only a small fraction of the available registers. see the register map section for a list of supported mmd device addresses and their associated register addresses. the following two standard registers serve as the portal registers to access the indirect mmd registers. ? standard r egister dh ? mmd access ? control ? standard r egister eh ? mmd access ? register/data table 12. portal registers (access t o indirect mmd registers) address name description mode default register dh ? mmd access ? control d.15:14 mmd ? operation mode for th e selected mmd device address (b its [4:0] of this register), these two bits select one of the following register or data operations and the usage for mmd access ? register/data (reg. eh). 00 = register 01 = data, no post increment 10 = data, post increment on reads and writes 11 = data, post increment on writes only rw 00 d.13:5 reserved reserved rw 00_0000_000 d.4:0 mmd ? device address these five bits set the mmd device address. rw 0_0000 register eh ? mmd access ? register/data e.15:0 mmd ? register/data for the selected mmd device address (reg. dh, b its [4:0]), when reg. dh, b its [15:14] = 00, this register contains the read/write register address for the mmd d evice a ddress. otherwise, this register contains the rea d/write data value for the mmd device a ddress and its selected register address. see also register dh, b its [15:14] descriptions for post incremen t reads and writes of this register for data operation. rw 0000_0000_0000_0000
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 49 revision 1.2 examples: mmd register write write mmd ? device address 1fh, register 0h = 0001h to enable link - up detection to trigger pme for w o l. 1. write r egister dh with 001fh // set up register address for mmd ? device address 1fh. 2. write r e gister eh with 0000h // select r egister 0h of mmd ? device address 1fh. 3. write r egister dh with 401fh // select register data for mmd ? device address 1fh, register 0h. 4. writ e r egister eh with 0001h // write value 0001h to mmd ? device address 1fh, register 0h. mmd register read read mmd ? device address 1fh, register 19h ? 1bh for the magic packet?s mac address 1. write r egister dh with 001fh // set up register address for mmd ? device address 1fh. 2. write r egister eh with 0019h // select r egister 19h of mmd ? device address 1fh. 3. write r egister dh with 801fh // select register data for mmd ? device address 1fh, register 19h // with post increments 4. read r egister eh // read data in mmd ? device address 1fh, register 19h. 5. read r egister eh // read data in mmd ? device address 1fh, register 1ah. 6. read r egister eh // read data in mmd ? device address 1fh, register 1bh.
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 50 revision 1.2 mmd registers ? descriptions address name description mode ( 8 ) default mmd address 1 h, register 0 h ? pma/pmd control 1 1. 0.15 :13 reserved reserved rw 000 1.0.12 lpi enable lower power idle enable rw 0 1. 0. 11:0 reserved reserved rw 0000_0000_0000 mmd address 1h, register 1 h ? pma/pmd status 1 1.1 .15 :9 reserved reserved ro 0000_000 1.1.8 lpi state entered 1 = pma/pmd has entered lpi state 0 = pma/pmd has not entered lpi state ro/lh 0 1.1.7:4 reserved reserved ro 0000 1.1.3 lpi state indication 1 = pma/pmd is currently in lpi state 0 = pma/pmd is currently not in lpi state ro 0 1.1.2:0 reserved reserved ro 000 mmd address 7h, re gister 3c h ? eee advertisement 7.3c.15:3 reserved reserved ro 0000_0000_0000_0 7.3c.2 1000base -t eee capable 0 = 1000mbps eee is not supported ro 0 7.3c.1 100base - tx eee capable 1 = 100mbps eee capable 0 = no 100mbps eee capability this bit is set to ?0? as the default after power -up or reset. set this bit to ?1? to enable 100mbps eee mode. rw 0 7.3c.0 reserved reserved ro 0 mmd address 7h, register 3d h ? eee link partner advertisement 7.3d.15:3 reserved reserved ro 0000_0000_0000_0 7.3d.2 1000base -t eee capable 1 = 1000mbps eee capable 0 = no 1000mbps eee capability ro 0 7.3d.1 100base - tx eee capable 1 = 100mbps eee capable 0 = no 100mbps eee capability ro 0 7.3d.0 reserved reserved ro 0 mmd address 1ch, re gister 4 h ? dsp 10base - t/10base - te control 1c.4.15 reserved reserved rw 0 1c.4.14 reserved reserved ro 0 1c.4.13 dsp 10base - t/10base - te mode select 1 = standard 10base - t (2.5v tx amplitude) and also set standard register 13h, bit [4] to ?0?. 0 = eee 10base - te (1.75v tx amplitude) and also set standard register 13h, bit [4] to ?1?. rw 1 1c.4.12 reserved reserved rw 0 1c.4.11:0 reserved reserved ro 0000_0000_0000 note: 8. rw = read/write. ro = read only. lh = latch high.
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 51 revision 1.2 mmd registers ? descriptions (continued) address name description mode ( 8 ) default mmd address 1fh, register 0h ? wake - on - lan ? control 1f.0.15:14 pme output select these two bits work in conjunction with reg. 16 h, bit [15] for pme enable to define the output for pins 1 8 and 23. intrp/pme_n2 (pin 1 8 ) 00 = intrp output 01 = pme_n2 output 10 = intrp and pme_n2 output 11 = reserved led0/pme_n1 (pin 23 ) 00 = pme_n1 output 01 = led0 output 10 = led0 output 11 = pme_n1 output rw 00 1f.0.13:7 reserved reserved ro 00_0000_0 1f.0.6 magic packet detect enable 1 = enable magic - packet detection 0 = disable magic - packet detection rw 0 1f.0.5 custom - packet type 3 detect enable 1 = enable custom - packet, type 3 detection 0 = disable custom - packet, type 3 detection rw 0 1f.0.4 custom - packet type 2 detect enable 1 = enable custom - packet, type 2 detection 0 = disable custom - packet, type 2 detection rw 0 1f.0.3 custom - packet type 1 detect enable 1 = enable custom - packet, type 1 detectio n 0 = disable custom - packet, type 1 detection rw 0 1f.0.2 custom - packet type 0 detect enable 1 = enable custom - packet, type 0 detection 0 = disable custom - packet, type 0 detection rw 0 1f.0.1 link - down detect enable 1 = enable link - down detection 0 = disable link - down detection rw 0 1f.0.0 link - up detect enable 1 = enable link - up detection 0 = disable link - up detection rw 0
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 52 revision 1.2 mmd registers ? descriptions (continued) address name description mode ( 8 ) default mmd address 1fh, register 1 h ? wake - on - lan ? customized packet, type 0, mask 0 mmd address 1fh, register 7 h ? wake - on - lan ? customized packet, type 1, mask 0 mmd address 1fh, register d h ? wake - on - lan ? customized packet, type 2, mask 0 mmd address 1fh, register 13 h ? wake - on - lan ? customized packet, type 3, mask 0 1f.1.15:0 1f.7.15:0 1f.d.15:0 1f.13.15:0 custom packet type x mask 0 this register selects the bytes in the firs t 16 bytes of the packet (bytes 1 thru 16) that will be used for crc calculation. for each bit in this register, 1 = byte is selected for crc calculation 0 = byte is not selected for crc calculation the register - bit to packet - byte mapping is as follows: b it [15] : byte -16 ? : ? bit [1] : byte -2 bit [0] : byte -1 rw 0000_0000_0000_0000 mmd address 1fh, register 2 h ? wake - on - lan ? customized packet, type 0, mask 1 mmd address 1fh, register 8 h ? wake - on - lan ? customized packet, type 1, mask 1 mmd address 1fh, register e h ? wake - on - lan ? customized packet, type 2, mask 1 mmd address 1fh, register 14 h ? wake - on - lan ? customized packet, type 3, mask 1 1f.2.15:0 1f.8.15:0 1f.e.15:0 1f.14.15:0 custom packet type x mask 1 this register selects the bytes in the second 16 bytes of the packet (bytes 17 thru 32) that will be used for crc calculation. for each bit in this register, 1 = byte is selected for crc calculation 0 = byte is not selected for crc calculation the register - bit to packet - byte mapping is as follows: bit [15] : byte -32 ? : ? bit [1] : byte -18 bit [0] : byte -17 rw 0000_0000_0000_0000
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 53 revision 1.2 mmd registers ? descriptions (continued) address name description mode ( 8 ) default mmd address 1fh, register 3 h ? wake - on - lan ? customized packet, type 0, mask 2 mmd address 1fh, register 9 h ? wake - on - lan ? customized packet, type 1, mask 2 mmd address 1fh, regist er f h ? wake - on - lan ? customized packet, type 2, mask 2 mmd address 1fh, register 15 h ? wake - on - lan ? customized packet, type 3, mask 2 1f.3.15:0 1f.9.15:0 1f.f.15:0 1f.15.15:0 custom packet type x mask 2 this register selects the bytes in the third 16 bytes of the packet (bytes 33 thru 48) that will be used for crc calculation. for each bit in this register, 1 = byte is selected for crc calculation 0 = byte is not selected for crc calculation the register - bit to packet - byte mapping is as follows: bi t [15] : byte -48 ? : ? bit [1] : byte -34 bit [0] : byte -33 rw 0000_0000_0000_0000 mmd address 1fh, register 4 h ? wake - on - lan ? customized packet, type 0, mask 3 mmd address 1fh, register a h ? wake - on - lan ? customized packet, type 1, mask 3 mmd address 1fh, register 10 h ? wake - on - lan ? customized packet, type 2, mask 3 mmd address 1fh, register 16 h ? wake - on - lan ? customized packet, type 3, mask 3 1f.4.15:0 1f.a.15:0 1f.10.15:0 1f.16.15:0 custom packet type x mask 3 this register selects the bytes in the fourth 16 bytes of the packet (bytes 49 thru 64) that will be used for crc calculation. for each bit in this register, 1 = byte is selected for crc calculation 0 = byte is not selected for crc calculation the register - bit to packet - byte mapping is as follows: bit [15] : byte -64 ? : ? bit [1] : byte -50 bit [0] : byte -49 rw 0000_0000_0000_0000 mmd address 1fh, register 5 h ? wake - on - lan ? customized packet, type 0, expected crc 0 mmd address 1fh, register b h ? wake - on - lan ? customized packet, type 1, expected crc 0 mmd address 1fh, register 11 h ? wake - on - lan ? customized packet, type 2, expected crc 0 mmd address 1fh, register 17 h ? wake - on - lan ? customized packet, type 3, expected crc 0 1f.5.15:0 1f.b.15:0 1f.11.15:0 1f. 17.15:0 custom packet type x crc 0 this register stores the lower two bytes for the expected crc. bit [15:8] = byte 2 (crc [15:8]) bit [7:0] = byte 1 (crc [7:0]) the upper two bytes for the expected crc are stored in the following register. rw 0000_00 00_0000_0000
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 54 revision 1.2 mmd registers ? descriptions (continued) address name description mode ( 8 ) default mmd address 1fh, register 6 h ? wake - on - lan ? customized packet, type 0, expected crc 1 mmd address 1fh, register c h ? wake - on - lan ? customized packet, type 1, expected crc 1 mmd add ress 1fh, register 12 h ? wake - on - lan ? customized packet, type 2, expected crc 1 mmd address 1fh, register 18 h ? wake - on - lan ? customized packet, type 3, expected crc 1 1f.6.15:0 1f.c.15:0 1f.12.15:0 1f.18.15:0 custom packet type x crc 1 this register stores the upper two bytes for the expected crc. bit [15:8] = byte 4 (crc [31:24]) bit [7:0] = byte 3 (crc [23:16]) the lower two bytes for the expected crc are stored in the previous register. rw 0000_0000_0000_0000 mmd address 1fh, register 19 h ? wake - on - lan ? magic packet, mac -da -0 1f.19.15:0 magic packet mac -da -0 this register stores the lower two bytes of the destination mac address for the magic packet. bit [15:8] = byte 2 (mac address [15:8]) bit [7:0] = byte 1 (mac address [7:0]) the upper four bytes of the destination mac address are stored in the following two registers. rw 0000_0000_0000_0000 mmd address 1fh, register 1a h ? wake - on - lan ? magic packet, mac -da -1 1f.1a.15:0 magic packet mac -da -1 this register stores the middle two bytes of the destination mac address for the magic packet. bit [15:8] = byte 4 (mac address [31:24]) bit [7:0] = byte 3 (mac address [23:16]) the lower two bytes and upper two bytes of the destination mac address are stored in the previous a nd following registers, respectively. rw 0000_0000_0000_0000 mmd address 1fh, register 1b h ? wake - on - lan ? magic packet, mac -da -2 1f.1b.15:0 magic packet mac -da -2 this register stores the upper two bytes of the destination mac address for the magic packet. bit [15:8] = byte 6 (mac address [47:40]) bit [7:0] = byte 5 (mac address [39:32]) the lower four bytes of the destination mac address are stored in the previous two registers. rw 0000_0000_0000_0000
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 55 revision 1.2 absolute maximum ratings ( 9 ) supply voltage (v in ) (v dd_1.2 ) .................................................. ? 0.5v to +1.8v (v ddio , v dda_3.3 ) ...................................... ? 0.5v to +5.0v input voltage (all inputs) .............................. ? 0.5v to +5.0v output voltage (all outputs) ......................... ? 0.5v to +5.0v lead temperature (soldering, 10s) ............................ 260c storage temperature (t s ) ......................... ? 55c to +150c operating ratings ( 10 ) supply voltage (v ddio_3.3 , v dda_3.3 ) .......................... +3.135v to +3.465v (v ddio_2.5 ) ........................................ +2.375v to +2.625v (v ddio_1.8 ) ........................................ +1.710v to +1.890v ambient temperature (t a , commercial) ...................................... 0 c to +70 c (t a , industrial) ....................................... ? 40 c to +85 c maximum junction temperature (t j max.) ................ 125c thermal resistance ( ja ) .................................... 49.22 c/w thermal resistance ( jc ) .................................... 25.65 c/w electrical characteristics ( 11) symbol parameter condition min . typ . max . units supply cur rent (vddio, v dda_3.3 = 3.3v) ( 12 ) i dd1_3.3v 10base -t full - duplex traffic @ 100% utilization 41 ma i dd2_3.3v 100base -tx full - duplex traffic @ 100% utilization 47 ma i dd3 _3.3v eee (100mbps) mode tx and rx paths in lpi state with no traffic 23 ma i dd4 _3.3v edpd mode ethernet cable disconnected (reg. 18h.11 = 0) 20 ma i dd5 _3.3v power - down mode software power - down (reg. 0h.11 = 1) 4 ma cmos level inputs v ih input high voltage v ddio = 3.3v 2.0 v v ddio = 2.5v 1.8 v ddio = 1.8v 1.3 v il input low voltage v ddio = 3.3v 0.8 v v ddio = 2.5v 0.7 v ddio = 1.8v 0.5 |i in | input current v in = gnd ~ vddio 10 a cmos level outputs v oh output high voltage v ddio = 3.3v 2.4 v v ddio = 2.5v 2.0 v ddio = 1.8v 1.5 v ol output low voltage v ddio = 3.3v 0.4 v v ddio = 2.5v 0.4 v ddio = 1.8v 0.3 |i oz | output tri - state leakage 10 a led output i led output drive current led0 pin 8 ma notes: 9. exceeding the absolute maximum ratings may damage the device. stresses greater than the absolute maximum rating can cause permanent damage to the device. operation of the device at these or any other conditions above those specified in the operating section s of this specification is not implied. maximum conditions for extended periods may affect reliability. 10. the device is not guaranteed to function outside its operating ratings. 11. t a = 25c. specification for packaged product only. 12. current consumption is for the single 3.3v supply ksz8091r na/rnd device only, and includes the transmit driver current and the 1.2v supply voltage (vdd_1.2) that are supplied by the ksz8091rna/rnd
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 56 revision 1.2 electrical characteristics ( 11) (continued) symbol parameter condition min . typ . max . units all pull - up/pull- down pins (including strapping pins) pu internal pull - up resistance v ddio = 3.3v 30 45 73 k v ddio = 2.5v 39 61 102 v ddio = 1.8v 48 99 178 pd internal pull - down resistance v ddio = 3.3v 26 43 79 k v ddio = 2.5v 34 59 113 v ddio = 1.8v 53 99 200 100base - tx transmit (measured differentially after 1:1 transformer) v o peak differential output voltage 100 termination across differential output 0.95 1.05 v v imb output voltage imbalance 100 termination across differential output 2 % t r , t f rise/fall time 3 5 ns rise/fall time imbalance 0 0.5 ns duty cycle distortion 0.25 ns overshoot 5 % output jitter peak -to - peak 0.7 ns 10base - t transmit (measured differentially after 1:1 transformer) v p peak differential output voltage 100 termination across differential output 2.2 2.8 v jitter added peak -to - peak 3.5 ns t r , t f rise/fall time 25 ns 10base - t receive v sq squelch threshold 5mhz square wave 400 mv transmitter ? drive setting v set reference voltage of i set r(i set ) = 6.49k 0.65 v ref_clk output 50mhz rmii clock output jitter peak -to - peak (applies only to rmii ? 25mhz clock mode) 300 ps 100mbps mode ? industrial applications parameters t llr link loss reaction (indication) time link loss detected at receive differential inputs to phy signal indication time for each of the following: 1 . for led mode 01, link led output changes from low (link - up) to high (link - down). 2 . intrp pin asserts for link - down status change. 4.4 s
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 57 revision 1.2 timing diagrams rmii timing figure 13 . rmii timing ? data received from rmii figure 14 . rmii timing ? data input to rmii table 13. rmii timing parameters ? ksz80 91rna/rnd (25mhz input to xi pin, 50mhz output from ref_clk pin) timing parameter description min. typ. max. unit t cyc clock cycle 20 ns t 1 setup time 4 ns t 2 hold time 2 ns t od output delay 7 10 13 ns table 14. rmii timing parameters ? ksz80 91rna/rnd (50mhz input to xi pin) timing parameter description min. typ. max. unit t cyc clock cycle 20 ns t 1 setup time 4 ns t 2 hold time 2 ns t od output delay 8 11 13 ns
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 58 revision 1.2 auto - negotiation timing figure 15 . auto - negotiation fast link pulse (flp) timing table 15. auto - negotiation fast link pulse (flp) timing parameters timing parameter description min. typ. max. unit t btb flp burst to flp burst 8 16 24 ms t flpw flp burst width 2 ms t pw clock/data pulse width 100 ns t ctd clock pulse to data pulse 55.5 64 69.5 s t ctc clock pulse to clock pulse 111 128 139 s number of clock/data pulses per flp burst 17 33
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 59 revision 1.2 mdc/mdio timing figure 16 . mdc/mdio timing table 16. mdc/mdio timing parameters timing parameter description min. typ. max. unit fc mdc clock frequency 2.5 10 mhz t p mdc period 400 ns t md1 mdio (phy input) setup to rising edge of mdc 10 ns t md2 mdio (phy input) hold from rising edge of mdc 4 ns t md3 mdio (phy output) delay from rising edge of mdc 5 222 ns
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 60 revision 1.2 power - up/reset timing the ksz80 91rna/rnd reset timing requirement is summarized in figure 17 and table 17 . figure 17 . power - up/reset timing table 17. power - up/reset timing parameters timing parameter description min. typ. max. unit t vr supply voltage (v ddio, v dda_3.3 ) rise time 300 s t sr stable supply voltage (v ddio, v dda_3.3 ) to reset high 10 ms t cs configuration setup time 5 ns t ch configuration hold time 5 ns t rc reset to strap - in pin output 6 ns the supply voltage ( v ddio and v dda_3.3 ) power - up waveform should be monotonic. the 300 s minimum rise time is from 10% to 90%. for warm reset, the reset (rst#) pin should be asserted low for a minimum of 500 s. the strap - in pin values are read and updated at the de - assertion of res et. after the de - assertion of reset, wait a minimum of 100 s before starting programming on the miim (mdc/mdio) interface.
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 61 revision 1.2 reset circuit figure 18 shows a reset circuit recommended for powering up the ksz80 91rna/rnd if reset is triggered by the power supply. figure 18 . recommended reset circuit figure 19 s hows a reset circuit recommended for applications where reset is driven by another device (for example, the cpu or an fpga). the reset out r st_out_n from cpu/fpga provides the warm reset after power up reset . d2 is used if using different vddio between the switch and cpu/fpga, otherwise, the different vddio will fight each other. if different vddio have to use in a special case, a low vf (<0.3 v) diode is required (for example, vishay?s bat54, mss1p2l and so on), or a level shifter device can be used too. if ethernet device and cpu/fpga use same vddio voltage, d2 can be removed to connect both devices directly. usually, ethernet device and cpu/f pga should use same vddio voltage. figure 19 . recommended reset circuit for interfacing with cpu/fpga reset output
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 62 revision 1.2 reference circuits ? led strap- in pin the pull - up, float, and pull - down reference circuits for the led0 /anen_speed strapping pin are shown in figure 20 for 3.3v and 2.5v vddio. figure 20 . reference circuits for led strapping pin for 1.8v vddio, led indication support is not recommended due to the low voltage. without the led indicator, the anen_ speed strapping pin is functional with a 4.7k pull - up to 1.8v vddio or float for a value of ?1?, and with a 1.0k pull - down to ground for a value of ?0?. note: if using rj45 j acks with integrated leds and 1.8v vddio, a level shifting is required from led 3.3v to 1.8v. for example, use a bipolar transistor or a level shift device.
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 63 revision 1.2 reference clock ? connection and selection a crystal or ext ernal clock source, such as an oscillator, is used to provide the reference clock for the ksz80 91rna/rnd . for the ksz80 91rna/rnd in rmii ? 25mhz clock mode, the reference clock is 25 mhz. the crystal / refe rence clock connections to xi (pin 8) and xo (p in 7), and the crystal / reference clock selection criteria, are provided in figure 21 and table 18 . figure 21 . 25mhz crystal/oscillator reference clock connection table 18 . 25mhz crystal /reference clock selection criteria characteristics value units frequency 25 mhz frequency tolerance (max.) () 50 ppm crystal series resistance (typ.) 40 crystal load capacitance (typ.) 22 pf note: 13. 60ppm for over temperature crystal. for the ksz80 9 1rn a/rnd in rmii ? 50mhz clock mode, the reference clock is 50mhz. the reference clock connection to xi (pin 8) and the reference clock selection criteria are provided in figure 22 and table 19 . figure 22 . 50mhz oscillator / reference clock connection table 19 . 50mhz oscillator/ reference clock selection criteria characteristics value units frequency 50 mhz frequency tolerance (max.) 50 ppm
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 64 revision 1.2 magnetic ? connection and selection a 1:1 isolation transformer is required at the line interface. use one with integrated common - mode chokes for designs exceeding fcc requirements. the ksz80 91rna/rnd design incorporates voltage - mode transmit drivers and on - chip terminations. with the volt age- mode implementation, the transmit drivers supply the common - mode voltages to the two differential pairs. therefore, the two transformer center tap pins on the ksz80 91rna/rnd side should not be connected to any power supply source on the board; instead, the center tap pins should be separated from one another and connected through separate 0.1f common - mode capacitors to ground. separation is required because the common - mode voltage is different between transmitting and receiving differential pairs . figure 23 shows the typical magnetic interface circuit for the ksz80 91rna/rnd . figure 23 . typical magnetic interface circuit
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 65 revision 1.2 table 20 lists recommended magnetic characteristics. table 20. magnetics selection criteria parameter value test condition turns ratio 1 ct : 1 ct open - circuit inductance (min.) 350 h 100mv, 100khz, 8ma insertion loss (typ.) ? 1.1db 100khz to 100mhz hipot (min.) 1500vrms table 21 is a list of compatible single - port magnetics with separated transformer center tap pins on the phy chip side that can be used with the ksz80 91rna/rnd . table 21. comp atible single - port 10/100 magnetics manufacturer part number temperature range magnetic + rj -45 bel fuse s558 - 5999-u7 0c to 70c no bel fuse si - 46001-f 0c to 70c yes bel fuse si - 50170-f 0c to 70c yes delta lf8505 0c to 70c no halo hfj11 - 2450e 0c to 70c yes halo tg110 - e055n5 ? 40c to 85c no lankom lf - h41s -1 0c to 70c no pulse h1102 0c to 70c no pulse h1260 0c to 70c no pulse hx1188 ? 40c to 85c no pulse j00 - 0014 0c to 70c yes pulse jx0011d21nl ? 40c to 85c yes tdk tla - 6t718a 0c to 70c yes transpower hb726 0c to 70c no wurth/midcom 000- 7090- 37r - lf1 ? 40c to 85c no
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 66 revision 1.2 package information and recommended land pattern ( 14) 24- pin ( 4mm 4mm) qfn note: 14. package information is correct as of the publication date. for updates and most current information, go to www.micrel.com .
micrel, inc. ksz8091rna/ksz8091rnd august 31 , 2015 67 revision 1.2 micrel, inc. 2180 fortune drive san jose, ca 95131 usa tel +1 (408) 944 - 0800 fax +1 (408) 474- 1000 web http://www.micrel.com micrel, inc. is a leading global manufacturer of ic solutions for the worldwide high performance linear and power, lan, and t iming & communications markets. the company?s products include advanced mixed - signal, analog & power semiconductors; high - performance communication, clock management, mems - based clock oscillators & crystal - less clock generators, ethernet switches, and physical layer transceiver ics. company customers include leading manufact urers of enterprise, consumer, industrial, mobile, telecommunications, automotive, and computer products. corporation headquarters and state - of - the - art wafer fabrication facilities are located in san jose, ca, with regional sales and support offices and advanced technology design centers situated throughout the americas, europe, and asia. additionally, the company maintains an extensive network of distributors and reps worldwide. micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this datasheet. this information is not intended as a warranty and micrel does not assume responsibility for its use. micrel reserves the right to change circuitry, specifications and descriptions at any ti me without notice. no license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. except as provided in micrel?s terms and conditions of sale for such products, m icrel assumes no li ability whatsoever, and micrel disclaims any express or implied warranty relating to the sale and/or use of micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copy right, or other intellectual property right. micrel products are not designed or authorized for use as components in life support appliances, devices or systems where mal function of a product can reasonably be expected to result in personal injury. life s upport devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. a purchaser?s u se or sale of micrel products for use in life support appliances, devices or systems is a purchaser?s own risk and purchaser agrees to fully indemnify micrel for any damages resulting from such use or sale. ? 20 13 micrel, incorporated.

▲Up To Search▲

Price & Availability of KSZ8091RND-EVAL

	To Download KSZ8091RND-EVAL Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .